299-01 Exam Details

  • Exam Code
    :299-01
  • Exam Name
    :Riverbed Certified Solutions Professional - Network Performance Management
  • Certification
    :Riverbed Certifications
  • Vendor
    :Riverbed
  • Total Questions
    :250 Q&As
  • Last Updated
    :May 29, 2026

Riverbed 299-01 Online Questions & Answers

  • Question 151:

    Which of the listed versions of NetFlow are supported by Cascade?

    A. v1 and v5
    B. v7
    C. v9
    D. all of the above
    E. none of the above

  • Question 152:

    Watches within Cascade Pilot refer to:

    A. Interactive views based upon time control.
    B. A time control window for creating trace clips.
    C. A panel displaying current time in the packet capture (pcap) file under analysis.
    D. A triggering and alerting capability based upon traffic views.
    E. A triggering and alerting capability using an optional fault management add-on for monitoring routers and switches.

  • Question 153:

    What mechanism does Cascade Profiler use to identify the switch port a host is attached to and the hosts associated MAC address?

    A. SNMP traps from the switches and routers
    B. NetFlow v9
    C. SNMP polling of the switches and routers
    D. All of the above
    E. None of the above

  • Question 154:

    Quality of Service information is obtained from what Cascade sources?

    A. Cascade Sensor only
    B. Cannot get QoS data on Cascade
    C. Cascade Sensor and Cascade Gateway
    D. CascadeFlow traffic only
    E. NetFlow and IPFIX traffic only

  • Question 155:

    How many items can be displayed in a single watched list in a Profiler Dashboard Content Block?

    A. Unlimited
    B. Ten
    C. Four
    D. Twenty

  • Question 156:

    For a TCP conversation that is non-optimized but being reported by a branch Steelhead appliance, the data center Steelhead appliance, and a data center Cascade Shark appliance, how is the Network RTT calculated?"

    A. The network setup (time between SYN to 1st ACK) is added together across the three segments: client to branch Steelhead appliance, branch Steelhead to DC Steelhead appliance, DC Steelhead appliance to the Server.
    B. The Server Delay time minus the Client Delay time.
    C. The top talker (server) that has sent the most data.
    D. The network setup time reported by the Cascade Shark appliance, which is the time between the reported client-->server SYN and the 1st client-->server ACK.

  • Question 157:

    Dynamic Host Configuration Protocol can be used by Cascade Profiler to:

    A. Allow user defined policies the ability to dynamically re-configure host IP parameters when the host triggers an event.
    B. Obtain an IP address on the Management interface on initial power-up.
    C. Obtain an IP address on the Auxiliary interface on initial power-up.
    D. Obtain host MAC address.
    E. A, B, C.

  • Question 158:

    If unable to connect to the Cascade Shark Appliance from the Cascade Pilot console it could be becausE. (Select 2)

    A. The correct communication port(s) are NOT open on the firewall between Cascade Pilot and Cascade Shark.
    B. The Cascade Shark is placed in "passthru" mode so Cascade Pilot access is not available
    C. The Cascade Shark appliance has no capture jobs configured.
    D. You may be running Cascade Pilot-Personal-Edition (PE). You need the full version of Cascade Pilot to connect to Cascade Shark.
    E. Trend/Index data is disabled on the Cascade Shark Appliance.

  • Question 159:

    How is the Cascade Pilot license activated?

    A. The license key is entered during installation. The license is activated either through an Internet connection or by phone.
    B. The license key is entered during installation. The license must be activated through an Internet connection.
    C. The license key is entered during installation. There is no activation but Cascade Pilot will detect if the license is already in use on the network.
    D. There is no license key activation. The software image is shipped with the license key installed.

  • Question 160:

    A SPAN port or Port Mirror differs from RSPAN technology in which way:

    A. A SPAN port captures traffic locally, an RSPAN captures traffic remotely
    B. A SPAN port captures traffic consistently, an RSPAN captures traffic randomly
    C. A SPAN port captures multiple ports while an RSPAN is "relational" and captures multiple VLANs (Relational LANs)
    D. They are both the same with different terms being used by different vendors
    E. A SPAN port is used on a Switch while a RSPAN is used on a Router

Tips on How to Prepare for the Exams

Nowadays, the certification exams become more and more important and required by more and more enterprises when applying for a job. But how to prepare for the exam effectively? How to prepare for the exam in a short time with less efforts? How to get a ideal result and how to find the most reliable resources? Here on Vcedump.com, you will find all the answers. Vcedump.com provide not only Riverbed exam questions, answers and explanations but also complete assistance on your exam preparation and certification application. If you are confused on your 299-01 exam preparations and Riverbed certification application, do not hesitate to visit our Vcedump.com to find your solutions here.