If a report table on Cascade Profiler includes the "Server Delay" column but shows no value for "Server Delay" in some cells, what are the possible causes? (Select 3)
A. The time span of the report does not cover any connection set-up points
B. Server delay is zero.
C. The protocol used by the application in not TCP-based.
D. Application traffic was not seen by a Cascade Sensor.
E. The server plug-in is needed to measure "Server Delay" and not functioning correctly.
Within the Cascade Pilot GUI, filtered items are often indicated:
A. With red text.
B. With yellow text.
C. With a funnel icon.
D. With a hash-mark icon.
Which of the following configuration changes can be used to reduce the number of alerts generated overall for a Service?
A. Edit each Service policy to increase the Tolerance slider for Low and High alerts.
B. Edit each Service policy and set a noise floor to specify the minimum amount of change that the policy can treat as deviation from normal behavior.
C. Edit the Service and select fewer metrics to monitor for each segment that comprises the Service.
D. Modify the location host group type used for monitoring end user traffic to use fewer groups (for example, Region instead of Site).
E. A, B, C, and D.
F. A and B only.
When editing a previously configured service policy, what options become available if you click the 'show advanced settings' checkbox? (Select 3)
A. Allows enabling/disabling the detection of dips in the metric.
B. Allows tuning of the tolerance range of the metric.
C. Allows setting of a noise floor for the metric.
D. Allows adjusting the notifications for the metric.
E. Allows enabling/disabling the detection of spikes in the metric.
How do Cascade Performance Analytics assist with Performance Monitoring?
A. By setting intelligent static thresholds for Application metrics and Interface metrics, tolerance can be determined. Cascade will use these thresholds and tolerances to report on deviations indicative of performance problems.
B. The Customer only needs to identify their critical hosts, interfaces and/or applications, and Cascade will automatically baseline their behavior and report on deviations indicative of performance problems.
C. The Performance Analytics use knowledge of hosts, interfaces, and/or applications are able to detect security threats such as host scans and worms.
D. After baselining is completed, Cascade can re-route congested traffic to avoid congested application delivery paths.
What is a good way to know whether all internal IP addresses seen by the Cascade Profiler have been grouped in a particular group type?
A. Run Automatic grouping for all group types.
B. Configure an Undefined group type with definition 0.0.0.0/0; confirm there are no entries when you 'view members' of this 'Undefined' group'.
C. There is no way to do this and successfully capture all the IP addresses.
D. Configure an Undefined group type with definition 0.0.0.0/32.
E. Run a report by hosts and look for undefined groups.
What are the two types of dashboards available within the Cascade Profiler GUI? (select 2)
A. Top Hosts
B. Top Applications
C. Public
D. Private
E. Devices and Interfaces Utilization
If unable to connect to the Cascade Shark Appliance from the Cascade Pilot console it could be becausE. (Select 2)
A. The correct communication port(s) are NOT open on the firewall between Cascade Pilot and Cascade Shark.
B. The Cascade Shark is placed in "passthru" mode so Cascade Pilot access is not available
C. The Cascade Shark appliance has no capture jobs configured.
D. You may be running Cascade Pilot-Personal-Edition (PE). You need the full version of Cascade Pilot to connect to Cascade Shark.
E. Trend/Index data is disabled on the Cascade Shark Appliance.
Cascade Profiler's Switch Integration feature uses SNMP and adds the capability for Cascade to report on which of the followinG. (Select 2)
A. User name
B. Host IP address
C. Host MAC address
D. The physical switch port a specific host is connected to
E. Switch port traffic levels
F. Switch port status
G. SNMP traps from the switch
What is the relationship between a Host Group and a Host Group Type in Cascade Profiler?
A. A Host Group Type is a container that may contain multiple Host Groups.
B. A Host Group Type defines the name of the Host Group.
C. They are the same thing.
D. Each Host Group must be defined by the Type of application it serves; this is the Host Group Type.
Nowadays, the certification exams become more and more important and required by more and more enterprises when applying for a job. But how to prepare for the exam effectively? How to prepare for the exam in a short time with less efforts? How to get a ideal result and how to find the most reliable resources? Here on Vcedump.com, you will find all the answers. Vcedump.com provide not only Riverbed exam questions, answers and explanations but also complete assistance on your exam preparation and certification application. If you are confused on your 299-01 exam preparations and Riverbed certification application, do not hesitate to visit our Vcedump.com to find your solutions here.