Cisco 200-355 Online Practice Questions and Exam Preparation

Cisco 200-355 Online Questions & Answers

• Question 371:

  Which two methods of authentication are available for Local EAP?

  A. LDAP and RADIUS
  B. Local and TACACS
  C. LDAP and Local
  D. Local and RADIUS
  C. LDAP and Local

• Question 372:

  Refer to the exhibit.

  

  What does the yellow shield with the exclamation mark indicate?

  A. The network uses open authentication and no encryption.
  B. The network uses an unsupported channel.
  C. The signal is too distorted to connect.
  D. The AP that is transmitting this SSID uses the wrong RF domain.
  E. This is the ad-hoc network.
  A. The network uses open authentication and no encryption.

  ---

  an exclamation mark inside a yellow shield is displayed if the SSID has no security [Open authentication, no encryption]), clicking Connect and completing the security parameters when applicable.

• Question 373:

  An indoor 1240 AP is booting and has obtained an IP address using DHCP. The AP has confirmed prior controller IP addresses from a previously joined mobility group stored in NVRAM. What is the next step the AP performs?

  A. DHCP option 43.
  B. DNS resolution of CISCO-LWAPP-CONTROLLER.localdomain.
  C. Layer 2 LWAPP discovery broadcast.
  D. Layer 3 LWAPP discovery broadcast.
  E. Ping each Cisco WLC to verify its current status.
  F. Select a Cisco WLC based on its position in the configured join selection sequence.
  A. DHCP option 43.

• Question 374:

  A customer has completed the installation of an 802.11ac greenfield deployment at their corporate headquarters. They would like to leverage 802.11ac enhanced speeds on the trusted employee WLAN. In order to configure the employee WLAN, what Layer 2 security policies are valid?

  A. WPA2 (TKIP)
  B. WPA(AES)
  C. OPEN
  D. WEP
  C. OPEN

• Question 375:

  Which official port should be used when configuring external RADIUS authentication on a Cisco WLC version 7.0?

  A. 49
  B. 1645
  C. 1646
  D. 1812
  E. 1813
  D. 1812

  ---

  RADIUS authentication uses UDP port 1812, while accounting uses UDP port 1813. Early implementations of RADIUS used ports 1645 and 1646, but that usage is obsolete. http://docstore.mik.ua/orelly/networking_2ndEd/fire/ch21_07.htm

• Question 376:

  Which two options are considered to be non-real-time applications? (Choose two.)

  A. social media
  B. video
  C. collaboration
  D. Citrix remote desktop
  E. email
  A. social media
  E. email

• Question 377:

  In the AP Layer 3 controller discovery process, after the LWAPP Discovery Request is broadcast on a local subnet, what is the next step that the AP takes?

  A. Determine whether the controller responses are the primary controller.
  B. Send an LWAPP discovery request to controllers learned via OTAP if operational.
  C. Send an LWAPP response to the master controller if known.
  D. Wait 5 seconds and resend a Discovery Request to the local subnet.
  B. Send an LWAPP discovery request to controllers learned via OTAP if operational.

• Question 378:

  Refer to the exhibit. Drag the steps for Open Authentication from the left and drop them in the correct order on the right.

  Select and Place:

  

  

• Question 379:

  During a wireless site survey, the signal strength drops significantly when outside of the room containing the access point. The building is made of wood and drywall. This is an example of which wireless anomaly?

  A. absorption
  B. refraction
  C. fading
  D. multipath
  E. reflection
  A. absorption

• Question 380:

  The wireless network is using controller-based APs and version 7.0 MR1. The APs appear to be connected properly to the controllers. A wireless user near one of the APs reports that they are unable to connect to the network with their preshared key. Which option shows the GUI path where you can check the connection status of that client?

  A. WLANs > WLAN_ID > Advanced
  B. Security > Clients
  C. Security > Advanced > Clients
  D. Monitor > Clients
  E. Wireless > 802.11b/g/n > clients
  D. Monitor > Clients

  ---

  Choose Monitor > Clients to open the Clients page.

  This page lists all of the clients that are associated to the controller's access points. It provides the following information for each client:

  http://www.cisco.com/c/en/us/td/docs/wireless/controller/7-4/configuration/guides/consolidated/b_cg74_CONSOLIDATED/b_cg74_CONSOLIDATED_chapter_010000000.html