Cisco 200-125 Online Practice Questions and Exam Preparation

Cisco 200-125 Online Questions & Answers

• Question 531:

  Which three options are switch port configuration, that can always avoid duplex mismatch errors between two switches? (Choose three)

  A. Set one side of the connection to full duplex and the other side to half duplex.
  B. Set both Sides of the connection to half duplex.
  C. Set one side of the connection to auto-negotiate and the other side to hall duplex
  D. Set both sides of the connection to full duplex
  E. Set one side of the connection to auto-negotiate and the other side to full duplex.
  F. Set both sides of the connection to auto-negotiate.
  B. Set both Sides of the connection to half duplex.
  D. Set both sides of the connection to full duplex
  F. Set both sides of the connection to auto-negotiate.

• Question 532:

  Which two pieces of information about a Cisco device can Cisco Discovery Protocol communicate?

  A. the native VLAN
  B. the VTP domain
  C. the spanning tree protocol
  D. the spanning-tree priority
  E. the trunking protocol
  B. the VTP domain
  E. the trunking protocol

• Question 533:

  Which symptom most commonly indicates that two connecting interfaces are configured with a duplex mismatch?

  A. the spanning-tree process shutting down
  B. collisions on the interface
  C. an interface with a down/down status
  D. an interface with an up/down status
  B. collisions on the interface

• Question 534:

  In which two situations should you use out-of-band management?

  A. when a network device fails to forward packets
  B. when you require ROMMON access
  C. when management applications need concurrent access to the device
  D. when you require administrator access from multiple locations
  E. when the control plane fails to respond
  A. when a network device fails to forward packets
  B. when you require ROMMON access

• Question 535:

  Refer to the exhibit.

  

  The network administrator requires easy configuration options and minimal routing protocol traffic. What two options provide adequate routing table information for traffic that passes between the two routers and satisfy the requests of the network administrator? (Choose two.)

  A. a dynamic routing protocol on InternetRouter to advertise all routes to CentralRouter.
  B. a dynamic routing protocol on InternetRouter to advertise summarized routes to CentralRouter.
  C. a static route on InternetRouter to direct traffic that is destined for 172.16.0.0/16 to CentralRouter.
  D. a dynamic routing protocol on CentralRouter to advertise all routes to InternetRouter.
  E. a dynamic routing protocol on CentralRouter to advertise summarized routes to InternetRouter.
  F. a static, default route on CentralRouter that directs traffic to InternetRouter.
  C. a static route on InternetRouter to direct traffic that is destined for 172.16.0.0/16 to CentralRouter.
  F. a static, default route on CentralRouter that directs traffic to InternetRouter.

  ---

  The use of static routes will provide the necessary information for connectivity while producing no routing traffic overhead.

• Question 536:

  For which two reasons was RFC 1918 address space define (Choose two)

  A. to preserve public IPv4 address space
  B. to reduce the occurrence of overlapping IP addresses
  C. to preserve public IPv6 address space
  D. reduce the size of ISP routing tables
  E. to support the NAT protocol
  A. to preserve public IPv4 address space
  B. to reduce the occurrence of overlapping IP addresses

• Question 537:

  Which NAT type is used to translate a single inside address to a single outside address?

  A. dynamic NAT
  B. NAT overload
  C. PAT
  D. static NAT
  D. static NAT

  ---

  Network address translation (NAT) is the process of modifying IP address information in IP packet headers while in transit across a traffic routing device.

  There are two different types of NAT:

  NAT

  PAT

• Question 538:

  Which command can you enter to set the default route for all traffic to an interface?

  A. router(config)#ip route 0.0.0.0 0.0.0.0 GigabitEthernet0/1
  B. router(config)#ip route 0.0.0.0 255.255.255.255 GigabitEthernet0/1
  C. router(config-router)#default-information originate
  D. router(config-router)#default-information originate always
  A. router(config)#ip route 0.0.0.0 0.0.0.0 GigabitEthernet0/1

• Question 539:

  Which action can change the order of entries in a named access-list?

  A. removing an entry
  B. opening the access-list in notepad
  C. adding an entry
  D. resequencing
  D. resequencing

• Question 540:

  Which mode are in PAgP? (Choose two)

  A. Auto
  B. Desirable
  C. Active
  D. Passive
  E. On
  A. Auto
  B. Desirable