Cisco 200-125 Online Practice Questions and Exam Preparation

Cisco 200-125 Online Questions & Answers

• Question 371:

  Which plane handles switching traffic through a Cisco router?

  A. control
  B. management
  C. data
  D. performance
  C. data

• Question 372:

  Which value is indicated by the next hop in a routing table?

  A. preference of the route source
  B. IP address of the remote router for forwarding the packets
  C. how the route was learned
  D. exit interface IP address for forwarding the packets
  B. IP address of the remote router for forwarding the packets

• Question 373:

  which command should you enter on an interface in a vendor-neutral EtherChannel so that it will be selected first to transmit packets?

  A. pagp system-priority 1024
  B. pagp port-priority 1024
  C. lacp system-priority 1024
  D. lacp port-priority 1024
  D. lacp port-priority 1024

• Question 374:

  Refer to the exhibit.

  

  All switch ports are assigned to the correct VLANs, but none of the hosts connected to SwitchA can communicate with hosts in the same VLAN connected to SwitchB. Based on the output shown, what is the most likely problem?

  A. The access link needs to be configured in multiple VLANs.
  B. The link between the switches is configured in the wrong VLAN.
  C. The link between the switches needs to be configured as a trunk.
  D. VTP is not configured to carry VLAN information between the switches.
  E. Switch IP addresses must be configured in order for traffic to be forwarded between the switches.
  C. The link between the switches needs to be configured as a trunk.

  ---

  In order to pass traffic from VLANs on different switches, the connections between the switches must be configured as trunk ports.

• Question 375:

  What are three broadband wireless technologies? (Choose three.)

  A. WiMax
  B. satellite Internet
  C. municipal Wi-Fi
  D. site-to-site VPN
  E. DSLAM
  F. CMTS
  A. WiMax
  B. satellite Internet
  C. municipal Wi-Fi

• Question 376:

  which command can you enter to re enable cisco discovery protocol on a local router after it has been

  disabled ?

  A. Router (config)# cdp run
  B. Router (config-if)# cdp run
  C. Router (config)# cdp enable
  D. Router (config-if)# cdp enable
  A. Router (config)# cdp run

• Question 377:

  Refer to the exhibit.

  

  Which two route codes indicate routes that use a Distance Vector Protocol? (Choose two)

  A. C
  B. D
  C. O
  D. R
  E. S
  B. D
  D. R

• Question 378:

  What are two enhancements that OSPFv3 supports over OSPFv2? (Choose two.)

  A. It requires the use of ARP.
  B. It can support multiple IPv6 subnets on a single link.
  C. It supports up to 2 instances of OSPFv3 over a common link.
  D. It routes over links rather than over networks.
  B. It can support multiple IPv6 subnets on a single link.
  D. It routes over links rather than over networks.

  ---

  Here is a list of the differences between OSPFv2 and OSPFv3:

  They use different address families (OSPFv2 is for IPv4-only, OSPFv3 can be used for IPv6-only or both protocols OSPFv3 introduces new LSA types OSPFv3 has different packet format OSPFv3 uses different flooding scope bits (U/S2/S1) OSPFv3 adjacencies are formed over link-local IPv6 communications OSPFv3 runs per-link rather than per-subnet OSPFv3 supports multiple instances on a single link, Interfaces can have multiple IPv6 addresses OSPFv3 uses multicast addresses FF02::5 (all OSPF routers), FF02::6 (all OSPF DRs) OSPFv3 Neighbor Authentication done with IPsec (AH) OSPFv2 Router ID (RID) must be manually configured, still a 32-bit number

  Reference: http://www.networkworld.com/article/2225270/cisco-subnet/ospfv3-for-ipv4-and- ipv6.html

• Question 379:

  What is the simplest IP SLA operation that can measure end-to-end response time between devices?

  A. ICMP path jitter
  B. ICMP path echo
  C. ICMP echo
  D. ICMP Jitter
  D. ICMP Jitter

• Question 380:

  which type of frame is larger than 9000 bytes?

  A. runt
  B. baby giant
  C. giant
  D. jumbo
  D. jumbo