Cisco 200-125 Online Practice Questions and Exam Preparation

Cisco 200-125 Online Questions & Answers

• Question 1061:

  Which two statements about IPv6 multicast address are true ?(choose two)

  A. If the liftime parameter is set to 1,the route is permanent.
  B. They use the prefix FC80::/8
  C. They use the prefix FF00::/8
  D. They identify a group of interfaces on different devices
  E. If the scope parameter is set to 5,the route is local to the node
  C. They use the prefix FF00::/8
  D. They identify a group of interfaces on different devices

• Question 1062:

  Which three elements are fields in a basic Ethernet data frame?(choose three)

  A. Length/Type
  B. Frame Check Sequence
  C. Version
  D. Preamble
  E. Time to Live
  F. Header Checksum
  A. Length/Type
  B. Frame Check Sequence
  D. Preamble

• Question 1063:

  Scenario

  Refer to the topology. Your company has connected the routers R1, R2, and R3 with serial links. R2 and R3 are connected to the switches SW1 and SW2, respectively. SW1 and SW2 are also connected to the routers R4 and R5.

  The EIGRP routing protocol is configured.

  You are required to troubleshoot and resolve the EIGRP issues between the various routers.

  Use the appropriate show commands to troubleshoot the issues.

  

  Router R6 does not form an EIGRP neighbor relationship correctly with router R1. What is the cause for this misconfiguration?

  A. The K values mismatch.
  B. The AS does not match.
  C. The network command is missing.
  D. The passive interface command is enabled.
  A. The K values mismatch.

• Question 1064:

  Which two types of NAT addresses are used in a Cisco NAT device? (Choose two.)

  A. inside local
  B. inside global
  C. inside private
  D. outside private
  E. external global
  F. external local
  A. inside local
  B. inside global

• Question 1065:

  Which switching method duplicates the first six bytes of a frame before making a switching decision?

  A. fragment-free switching
  B. store and-forward switching
  C. cut through switching
  D. ASIC switching
  C. cut through switching

  ---

  Explanation: Cut and Through method has lowest latency. In this method Switch only read first six bytes from frame after the preamble. These six bytes are the destination address of frame. This is the fastest method of switching. This method

  also processes invalid frames.

  Only advantage of this method is speed.

• Question 1066:

  Which two of these statements are true of IPv6 address representation? (Choose two.)

  A. There are four types of IPv6 addresses: unicast, multicast, anycast, and broadcast.
  B. A single interface may be assigned multiple IPv6 addresses of any type.
  C. Every IPv6 interface contains at least one loopback address.
  D. The first 64 bits represent the dynamically created interface ID.
  E. Leading zeros in an IPv6 16 bit hexadecimal field are mandatory.
  B. A single interface may be assigned multiple IPv6 addresses of any type.
  C. Every IPv6 interface contains at least one loopback address.

  ---

  A single interface may be assigned multiple addresses of any type (unicast, anycast, multicast). Every IPv6-enabled interface must contain at least one loopback and one link-local address. Optionally, every interface can have multiple unique local and global addresses.

  Reference: IPv6 Addressing at a Glance ?Cisco PDF

• Question 1067:

  Which two statements are true for multicast MAC address directions?

  A. 01:00:5E:xx:xx:xx
  B. one to one
  C. 01 00 xx xxxxxxx
  D. 02 xx xxxxxxx
  E. one to many
  A. 01:00:5E:xx:xx:xx
  E. one to many

  ---

  The Internet authorities have reserved the multicast address range of 01:00:5E:00:00:00 to 01:00:5E:7F:FF:FF for Ethernet and Fiber Distributed Data Interface (FDDI) media access control (MAC) addresses.

• Question 1068:

  Which two TLVs does LLDP support?(choose two)

  A. system description
  B. port duplex
  C. management address
  D. native VLAN
  E. spanning tree
  A. system description
  C. management address

• Question 1069:

  Which two values can identify a switch stack on the network? (Choose two )

  A. the bridge ID
  B. the spanning tree priority
  C. the switch BIA
  D. the switch priority
  E. the management IP address of the device
  A. the bridge ID
  D. the switch priority

• Question 1070:

  After you configure the ip dns spoofing command globally on a device,under which two conditions is DNS spoofing enabled on the device?(Choose two)

  A. The DNS server queue limit id disabled
  B. The ip host command is disabled
  C. All configured IP name server addresses are removed
  D. The ip dns spoofing command is disabled on the local interface
  E. The no ip domain lookup command is configured
  C. All configured IP name server addresses are removed
  E. The no ip domain lookup command is configured