Riverbed Riverbed Certifications 199-01 Questions & Answers

• Question 321:

  What is the primary purpose of enabling Multiple Interface Support on the Interceptor?

  A. It allows for the ability to support multiple NICs on the Interceptor

  B. It allows the Interceptor appliance to communicate with Steelhead appliances and other Interceptor appliances via more than one In-path interface

  C. It allows the Interceptor appliance to communicate via Multicast to In-path interfaces on the Steelhead appliances

  D. It allows the Interceptor appliance to be managed by In-path interfaces as well as the Primary interface

  Correct Answer: B

• Question 322:

  The primary purpose of setting proxies (found on Networking ?Proxies) on the Interceptor is to:

  A. Allow for a Web or FTP proxy when specifying a URL on the Management Console or CLI

  B. Allow for another Interceptor to redirect on behalf of the current Interceptor

  C. Allow for Steelhead appliances to dynamically handle the load of another Steelhead appliance

  D. Allow for two Interceptor appliances to act redundantly in a serial configuration

  Correct Answer: A

• Question 323:

  Refer to the exhibit.

  

  What does the term resyncing mean?

  A. All Interceptor appliances have been connected and the appliances are transferring connection information

  B. All Interceptor appliances and all Steelhead appliances have been connected and the appliances are transferring connection information

  C. The connection has been established and the Interceptor appliance is transferring its state information

  D. The connection has been established and the devices are transferring their state information

  Correct Answer: D

• Question 324:

  Peer affinity is most closely related to:

  A. Parallel Interceptor redirection based on Sport ID and client IP

  B. Serial Interceptor redirection based on Sport ID to server

  C. Segstore ID Steelhead mapping based on Sport ID of Steelhead appliances

  D. The shipyard from which Riverbed is most likely to ship Interceptors

  Correct Answer: C

• Question 325:

  For a new connection, an Interceptor appliance has no peer affinity, which Steelhead appliance will the Interceptor appliance choose for the connection?

  A. The Interceptor appliance selects the Steelhead appliance with the least connections

  B. The Interceptor appliance selects the Steelhead that has the most connections

  C. The Interceptor appliance selects the most loaded Steelhead appliance

  D. The Interceptor appliance selects the Steelhead appliance with the most peer affinity

  Correct Answer: A

• Question 326:

  What is the command to verify a configuration of the Interceptor peers and peer neighbors?

  A. verify interceptor deployment

  B. service verify

  C. debug validate deployment

  D. config checker

  Correct Answer: C

• Question 327:

  To configure a Steelhead appliance for logical in-path mode, the following must be enabled in the General Service Settings page:

  A. Reset Existing Client Connections on Start Up

  B. Enable L4/PBR/WCCP Support on Interface wan0_0

  C. Enable Optimizations on Interface inpath0_0

  D. B and C

  E. A, B, and C

  Correct Answer: D

• Question 328:

  If a Steelhead appliance is configured for logical in-path mode:

  A. The Primary interface cannot be on the same subnet

  B. The LAN In-path interface will be disabled

  C. The WAN In-path interface will be disabled

  D. The Steelhead appliance listens for the Interceptor on TCP port 7860

  Correct Answer: B

• Question 329:

  The Interceptor appliance can be configured to redirect traffic to the Steelhead appliances via what methods?

  A. GRE

  B. L2

  C. ISIS

  D. Multicast

  E. Redirection is automatic and not configurable

  Correct Answer: E

• Question 330:

  What type of configuration must be used on a Steelhead appliance in order to communicate with an Interceptor appliance?

  A. In-path

  B. Out-of-path

  C. Logical in-path

  D. Physical in-path Hybrid Mode

  Correct Answer: C