Riverbed 199-01 Online Practice Questions and Exam Preparation

Riverbed 199-01 Online Questions & Answers

• Question 251:

  In a Steelhead deployment, the customer decides to use Full Transparency and block all incoming/outgoing TCP connections on port 7800 on their firewall. However, they are finding all TCP connections are passing through the Steelheads (even ones that should be optimized via the in-path rule set).

  If Full Transparency uses the original IP addresses and TCP ports for inner connections, what is needed to fix the problem?

  A. "no in-path enable"; since we don't really need in-path in this case
  B. "destination oobtransparency"; since the OOB (out-of-band) splice needs transparency also
  C. "inner connection max 50"; since the default inner connection pool count of 20 is insufficient
  D. No command needed, the connections are really optimized even though we report connections are passed through
  B. "destination oobtransparency"; since the OOB (out-of-band) splice needs transparency also

• Question 252:

  How do you clean the datastore on a Steelhead appliance? 1) > restart empty 2) > reload clean 3) # restart empty 4) # restart clean 5) (config) # reload clean

  A. 1, 2
  B. 2, 3
  C. 4, 5
  D. 3, 4, 5
  E. 1, 2, 3, 4, 5
  C. 4, 5

• Question 253:

  How does the Steelhead Mobile Controller provide Steelhead Mobile clients with the assigned policies and policy updates?

  A. Using the GID
  B. Using the SID
  C. Policies are pushed to all clients using IPSec
  D. The Steelhead Mobile client needs to be re-installed to update the policies
  E. Upon connection to the Steelhead appliance
  A. Using the GID

• Question 254:

  Refer to the exhibit.

  

  In the accompanying exhibit, SH3 and SH4 are able to optimize FTP and HTTP sessions between Client41 and the respective application hosts Server31 and Server32. However, optimization does not happen for Client42 and these application hosts. A quick check on SH3 and SH4 registers neither optimized nor pass-through traffic from Client42. Client42 is able to ping Client41 and the in-path address of SH4. Note that SH3 and SH4 are in auto-discovery mode. What is the likely cause?

  A. The default gateway of Client41 is configured wrong
  B. The default gateway of Client42 is configured wrong
  C. The default gateway of SH3 is configured wrong
  D. The default gateway of SH4 is configured wrong
  E. The routing protocol between R3 and R4 is configured wrong
  B. The default gateway of Client42 is configured wrong

• Question 255:

  A customer uses a single URL for a service that uses many servers with different certificates. What SSL options should be enabled to enhance performance?

  A. Passive key derivation
  B. SSL proxy support and SNI (Server name indication)
  C. SSL advanced mode
  D. Early start/late finish
  C. SSL advanced mode

• Question 256:

  -- Exhibit

  

  -- Exhibit -Refer to the exhibit. When USER1 tried to access Server 1, he sees the shown message on his Steelhead Mobile Client. What statements are true? (Select 2)

  A. "Optimization Status: Configuring " means that the user is making a change on his Steelhead Mobile client at that moment.
  B. "Optimization Status: Configuring " means that the policy has been changed on the Steelhead Mobile Controller and is being downloaded into the client at that moment.
  C. Any changes that are made on an active policy on the Steelhead Mobile Controller will only take effect after the client reboot.
  D. Any changes that are made on an active policy on the controller will take effect immediately.
  B. "Optimization Status: Configuring " means that the policy has been changed on the Steelhead Mobile Controller and is being downloaded into the client at that moment.
  D. Any changes that are made on an active policy on the controller will take effect immediately.

• Question 257:

  Which command will display current alarm status information?

  A. show stats alarm
  B. stats show alarm
  C. show alarm all
  D. alarm show all
  E. show all
  A. show stats alarm

• Question 258:

  In the exhibit,

  

  which interfaces should the WCCP router R1 listen to for multicast communication with the server-side Steelhead appliances, assuming the multicast address is 239.0.0.1? (Select 2)

  A. A
  B. B
  C. C
  D. D
  E. E
  D. D
  E. E

• Question 259:

  You are troubleshooting a TCP connection that is not being optimized. On the Current Connections report, you expand the connection and see the pass-through reason is `Pre-existing connection'.

  Without restarting the oprimization service, how could you get this connection to optimize?

  A. Reset the connection in the Current Connections report.
  B. Create a full-transparency in-path rule for the source and destination hosts.
  C. Create a fixed-target in-path rule for the source and destination hosts.
  D. Enable auto-kick-off on the default in-path rule.
  E. Enable Simplified Routing in `all' mode.
  A. Reset the connection in the Current Connections report.

• Question 260:

  When deploying Interceptor appliances on aggregated links, you must: (Select 2)

  A. configure each in-path interface to have a unique IP address
  B. configure WCCP
  C. configure the allow neighbor failure command
  D. configure each in-path interface to have the same IP address
  E. configure the no arp filter response command
  A. configure each in-path interface to have a unique IP address
  E. configure the no arp filter response command