Riverbed 199-01 Online Practice Questions and Exam Preparation

Riverbed 199-01 Online Questions & Answers

• Question 231:

  For a Steelhead Mobile solution to work properly, what port needs to be allowed by the device that Steelhead Mobile is installed on?

  A. 7800
  B. 7810
  C. 7801
  D. 7830
  E. 7840
  C. 7801

• Question 232:

  -- Exhibit

  

  -- Exhibit -In a WCCP environment with R3, SH10 and SH11, it was observed that SH11's WCCP state is "read error". What is the possible cause?

  A. The Steelhead is not receiving i-see-you messages from the router
  B. The Steelhead is not sending here-i-am messages to the router
  C. The Steelhead is not receiving removal query messages from the router
  D. Everything is in order ?working properly
  A. The Steelhead is not receiving i-see-you messages from the router

• Question 233:

  What configuration policies can be used on the SteelCentral Controller for SteelHead (SCC) for Interceptor deployments?

  A. The SCC can be used to create all configuration for the Interceptors and its associated SteelHeads, as long as all the devices are in the same SCC group.
  B. The SCC can create in-path rules policies the same as a SteelHead, as long as that is the only page enabled for the Interceptor.
  C. The SCC can be used to configure the cluster of registered Interceptors and SteelHeads. Then, in-path rules and load balancing rules can be pushed to the interceptors.
  D. The SCC can be used to create cluster policies, for the Interceptor to SteelHead connections only and not in-path or load balancing rules.
  E. The SCC can only monitor the health, backup the configuration and upgrade Interceptors. Policies are only for SteelHeads. Interceptors and SteelHead Mobile are not supported.
  C. The SCC can be used to configure the cluster of registered Interceptors and SteelHeads. Then, in-path rules and load balancing rules can be pushed to the interceptors.

• Question 234:

  You need to perform a tcpdump of traffic entering the Steelhead appliance's lan0_0 interface. Which of the following demonstrate the proper command format to perform the tcpdump and capture to a file?

  A. tcpdump –p lan0_0 –S 300 –w lancap.cap
  B. tcpdump –i lan0_0 –s 300 –w lancap.cap
  C. tcpdump –i lan0_0
  D. tcpdump –I lan0_0 –s 300
  E. tcpdump –i lan0_0 -3 300 –r lancap.cap
  B. tcpdump –i lan0_0 –s 300 –w lancap.cap

• Question 235:

  A SteelHead is running RiOS v8.6 and has an inpath0_0 IP address of 192.168.1.10. It is later upgraded from v8.6 to v9.0. As part of an IT project, the inpath0_0 IP address is changed to 10.10.10.10 and the configuration saved. Some time passes and the administrator decides to revert to RiOS v 8.6. It hasn't been factory reset. The appliance boots and the Management Console User Interface is reachable, however, optimization no longer works. What has happened?

  A. The web GUI SSL certificate is no longer trusted and the services require a restart.
  B. The licenses are no longer valid and will need to be replaced and the services restarted.
  C. It is not possible to revert to older versions of RiOS and the optimization service has stopped as a precaution.
  D. The configuration has reverted to the one running under v8.6 and the inpath0_0 IP address is back to 192.168.1.10.
  E. The configuration has been lost and the appliance is running factory default settings.
  D. The configuration has reverted to the one running under v8.6 and the inpath0_0 IP address is back to 192.168.1.10.

• Question 236:

  You see errors such as the following in the SteelHead messages log "error=SMB_SHUTDOWN_ERR_SEC_SIG_ENABLED". What do these indicate?

  A. SMB signing has been detected on SMB sessions which the SteelHead attempted to optimize, but SMB signing is not configured on the SteelHeads.
  B. The SteelHeads are configured to carry secure traffic over SSI and the inner channel failed to establish.
  C. The optimization service encountered an error, and the SMB blade has been shut down.
  D. The SteelHead encountered a kernel error and was forced to shut down.
  E. The server send a secure signal to terminate an optimized SMB session.
  A. SMB signing has been detected on SMB sessions which the SteelHead attempted to optimize, but SMB signing is not configured on the SteelHeads.

• Question 237:

  Using an Interceptor appliance is an alternative to what network designs? (Select 2)

  A. WCCP
  B. PBR
  C. Connection Forwarding
  D. Fixed-target rules
  E. Peering rules
  A. WCCP
  B. PBR

• Question 238:

  Which command shows the last boot partition and the next boot partition? (Select 2)

  A. show bootvar
  B. show images
  C. show info
  D. show bootpar
  E. show system
  F. show version
  A. show bootvar
  B. show images

• Question 239:

  The Group ID (GID) links which two policies? (Select 2)

  A. Optimization
  B. Acceleration
  C. Installation
  D. Endpoint
  E. Assignment
  B. Acceleration
  D. Endpoint

• Question 240:

  What type of configuration must be used on a Steelhead appliance in order to communicate with an Interceptor appliance?

  A. In-path
  B. Out-of-path
  C. Logical in-path
  D. Physical in-path Hybrid Mode
  C. Logical in-path