Cisco 100-105 Online Practice Questions and Exam Preparation

Cisco 100-105 Online Questions & Answers

• Question 61:

  

  Refer to the exhibit. Which feature is enabled by this configuration?

  A. static NAT translation
  B. a DHCP pool
  C. a dynamic NAT address pool
  D. PAT
  C. a dynamic NAT address pool

• Question 62:

  

  Refer to the exhibit. The enterprise has decided to use the network address 172.16.0.0. The network administrator needs to design a classful addressing scheme to accommodate the three subnets, with 30, 40, and 50 hosts, as shown. Which subnet mask would accommodate this network?

  A. 255.255.255.224
  B. 255.255.255.240
  C. 255.255.255.252
  D. 255.255.255.248
  E. 255.255.255.192
  E. 255.255.255.192

• Question 63:

  Which statement describes the effect of the overload keyword in the ip nat inside source list 90 interface ethernet 0/0 overload command?

  A. Addresses that match access list inside are translated to the IP address of the Ethernet 0/0 interface.
  B. Hosts that match access list inside are translated to an address in the Ethernet 0/0 network.
  C. Hosts on the Ethernet 0/0 LAN are translated to the address pool in access list 90.
  D. Addresses that match access list 90 are translated through PAT to the IP address of the Ethernet 0/0 interface.
  D. Addresses that match access list 90 are translated through PAT to the IP address of the Ethernet 0/0 interface.

• Question 64:

  Which OSI layer header contains the address of a destination host that is on another network?

  A. application
  B. session
  C. transport
  D. network
  E. data link
  F. physical
  D. network

• Question 65:

  What is the OSPF default frequency, in seconds, at which a Cisco router sends hello packets on a multi-access network?

  A. 10
  B. 40
  C. 30
  D. 20
  A. 10

• Question 66:

  In which two situations should you use out-of-band management?

  A. when a network device fails to forward packets
  B. when you require ROMMON access
  C. when management applications need concurrent access to the device
  D. when you require administrator access from multiple locations
  E. when the control plane fails to respond
  A. when a network device fails to forward packets
  B. when you require ROMMON access

• Question 67:

  

  What interfaces on Router1 have not had any configurations applied? (Choose two.)

  A. Ethernet 0
  B. FastEthernet 0/0
  C. FastEthernet 0/1
  D. Serial 0
  E. Serial 0/0
  F. Serial 0/1
  B. FastEthernet 0/0
  F. Serial 0/1

• Question 68:

  DRAG DROP

  Drag and drop the steps in the process of configuring an ACL to allow web access from a server on the left into the correct sequence on the right. Not all steps are used.

  Select and Place:

  

  

• Question 69:

  Client A cannot reach client B by its hostname. Which reason for the problem is most likely true?

  A. The connected router is using the default domain lookup configuration
  B. The hostname for client B is missing from the connected router
  C. A DNS server has been misconfigured
  D. Telnet has been disabled on the connected router.
  C. A DNS server has been misconfigured

• Question 70:

  What command can you enter to configure the switch as an authoritative ntp server with site id : XXXXXXXX?

  A. Switch(config)#ntp master 3
  B. Switch(config)#ntp peer IP 193.168.2.2
  C. Switch(config)#ntp server IP 193.168.22
  D. Switch(config)#ntp source IP 193.168.2.2
  A. Switch(config)#ntp master 3