VMware VCP-510 Online Practice Questions and Exam Preparation

VMware VCP-510 Online Questions & Answers

• Question 61:

  An administrator is configuring an ESXi 5.x host with two dual-port Fibre Channel (FC) HBAs. The FC storage array has four active storage processor ports. Zoning is configured on both fabrics, with ESXi HBA ports and the array ports in the same zone. There are two LUNs with VMFS datastores configured. Using Round Robin multipathing, what is the maximum number of paths that can be used to send data to the VMFS datastores at any given time?

  A. 2
  B. 3
  C. 1
  D. 4
  A. 2

• Question 62:

  An administrator is performing upgrades to ESXi 5.x from ESX 3.x and ESX 4.x hosts. What is true about this procedure?

  A. A direct, in-place upgrade can be performed only on ESX 4.1 and later hosts.
  B. ESX 3.x hosts can be upgraded, but require an upgrade to 4.x before 5.x.
  C. A direct, in-place upgrade can be performed only on ESX 4.5 and later hosts.
  D. A direct, in-place upgrade can be performed only on ESX 3.5 and later hosts.
  B. ESX 3.x hosts can be upgraded, but require an upgrade to 4.x before 5.x.

• Question 63:

  The remote console performance for a virtual machine on an ESXi host appears to be degraded. What are two possible causes of the problem? (Choose two)

  A. The virtual NIC assigned to the virtual machine has a speed or duplex mismatch.
  B. The physical NIC assigned to the virtual machine port group containing the affected virtual machine has a speed or duplex mismatch.
  C. The physical NIC assigned to the Service Console port group has a speed or duplex mismatch.
  D. The physical NIC assigned to the VMkernel port group has a speed or duplex mismatch.
  B. The physical NIC assigned to the virtual machine port group containing the affected virtual machine has a speed or duplex mismatch.
  D. The physical NIC assigned to the VMkernel port group has a speed or duplex mismatch.

• Question 64:

  When an explicit failover order has been configured on a virtual switch with multiple uplinks, what determines which uplink is used when a failover event occurs?

  A. The first available uplink that reports a positive link state
  B. The reported uptime for the surviving uplinks
  C. The next available uplink on the list
  D. The uplink with the shortest route
  C. The next available uplink on the list

• Question 65:

  Assuming that ballooning is possible, under which three circumstances might the VMkernel use a swap file for a running virtual machine? (Choose three.)

  A. The Mem.CtlMaxPercent value is between 10 and 25 percent.
  B. Memory cannot be reclaimed quickly enough.
  C. The virtual machine is starting up.
  D. VMware Tools is not installed.
  E. 50% of the configured memory has already been ballooned.
  A. The Mem.CtlMaxPercent value is between 10 and 25 percent.
  B. Memory cannot be reclaimed quickly enough.
  E. 50% of the configured memory has already been ballooned.

• Question 66:

  Which two events will result in a vSphere 5.x host running a virtual machine that contains an older virtual hardware version? (Choose two)

  A. a virtual machine is created on a vSphere 5.x host and virtual for the VM are created on a VMFS3 datastore.
  B. a virtual machine was migrated from a vSphere 4.x host.
  C. a virtual machine is created on a vSphere 5.x host with a with a vmxnet network adapter.
  D. a virtual machine is created on a vSphere 5.x host and attached to an existing virtual disk created with vSphere 4.x
  B. a virtual machine was migrated from a vSphere 4.x host.
  D. a virtual machine is created on a vSphere 5.x host and attached to an existing virtual disk created with vSphere 4.x

• Question 67:

  Which two conditions will cause a vMotion validation check to fail? (Choose two.)

  A. An active connection that matches an existing port group label on the target host
  B. Insufficient network bandwidth on the target virtual switch
  C. Different security policies on the target virtual switch
  D. An active connection to an internal virtual switch
  C. Different security policies on the target virtual switch
  D. An active connection to an internal virtual switch

• Question 68:

  Which methods can be used to migrate a VMkernel port from a vSphere Standard Switch to a vSphere Distributed Switch? (Choose two.)

  A. Use the Add Virtual Adapter wizard from the Manage Virtual Adapters window.
  B. Use the Manage Hosts wizard from the Configuration tab of the vDS.
  C. Use the Migrate Virtual Machine Networking option to select the port from a list.
  D. Edit the Network Adapter settings for the port and select a dvPort group from the list.
  A. Use the Add Virtual Adapter wizard from the Manage Virtual Adapters window.
  B. Use the Manage Hosts wizard from the Configuration tab of the vDS.

• Question 69:

  What is the size of a virtual machine .vswp file?

  A. The virtual machine .vswp file is equal to twice the amount of available memory configured for the virtual machine when it was created.
  B. The virtual machine .vswp file is equal to the amount of virtual memory (virtual machine available memory, plus virtual machine overhead) configured for the virtual machine when it was created.
  C. The virtual machine .vswp file is set to the amount of memory allocated minus any memory reservation.
  D. The virtual machine .vswp file is equal to the amount of available memory in the ESXi server.
  C. The virtual machine .vswp file is set to the amount of memory allocated minus any memory reservation.

• Question 70:

  Which of the following actions requires a reboot of an ESXi host

  A. Changing the number of ports on a virtual switch
  B. Implementing VLANs in a virtual switch
  C. Adding a second VMkernel port to a virtual switch
  D. Configuring a NIC team for a virtual switch
  A. Changing the number of ports on a virtual switch