NetApp NS0-593 Online Practice Questions and Exam Preparation

NetApp NS0-593 Online Questions & Answers

• Question 41:

  Your customer installed the shelf firmware for their NS224 shelf over a week ago, and the firmware has notupgraded on shelf 1 module B. The customer wants to know what the next steps would be to get the firmware upgraded after verifying that the shelf firmware is indeed loaded onto the system.

  Which step would you perform to complete the firmware upgrade?

  A. Reseat the NSM100 module.
  B. Reseat the disk in Bay 0.
  C. Power cycle the shelf.
  D. Reseat the PSU of the shelf.
  C. Power cycle the shelf.

• Question 42:

  Which two throughput elements are controlled by host applications? (Choose two.)

  A. operation size
  B. Jitter
  C. concurrency
  D. latency
  B. Jitter
  D. latency

• Question 43:

  Your customer added a new DS4246 shelf to their FAS2750 single-node system and created a new aggregate on the new shelf. Two weeks later, they log into Active IQ and discover the Medium Impact error shown below. Shelves with both connections via the same SAS path detected

  

  Referring to the exhibit, which statement is correct?

  A. In a FAS2750 system, the internal shelf is only seen on one path, and the external shelves are seen on two paths.
  B. The cables are cabled Incorrectly on the SAS stack.
  C. This situation is normal for a FA57750 single-node system.
  D. Active IQ Is not aware of the shelf configuration for a single-node system.
  C. This situation is normal for a FA57750 single-node system.

• Question 44:

  Your customer noticed in NetApp Active IQ that their NetApp Cloud Volumes ONTAP forAzure HA solution is no longer sending AutoSupport messages over HTTPS. A support ticket has been opened to find out why. No changes have been made to the Cloud Volumes ONTAP for Azure HA environment.

  In this scenario, which two autosupport command parameters should be used to validate that AutoSupport Is working properly? {Choose two.)

  A. -mail-hosts
  B. -transport
  C. -proxy-url
  D. -to
  A. -mail-hosts
  C. -proxy-url

• Question 45:

  You are deploying NetApp ONTAP Select. When trying to add VMware vCenter to the inventory, you receive the message shown below.

  Credential authentication failed for x.x.x.x with: HostConnectionFailed

  In this scenario, how would you correct this problem?

  A. Change the vCenter password.
  B. Change the IP address of the ONTAP Select Deploy VM.
  C. Change the gateway address of the ONTAP Select Deploy VM.
  D. Change the IP address of the vCenter server.
  A. Change the vCenter password.

• Question 46:

  A customer with an FC MetroClusterconfiguration that is running NetApp ONTAP 9.8 software experienced a site outage and wants to know why the MetroClusler configuration did not switch over to the other site. What are two reasons for this problem? (Choose two.)

  A. There was a failed PSU inthe switchover site.
  B. The ISLs were down between the sites.
  C. The site had unmirrored aggregates.
  D. An ISL link was not operating at 16Gbps.
  A. There was a failed PSU inthe switchover site.
  C. The site had unmirrored aggregates.

• Question 47:

  A storage administrator reports that a monitoring toot is reporting that the storage controller reads between 90% to 93% CPU use. You run the sysstat -m command against thenode in question.

  

  Referring to the exhibit, which statement is correct?

  A. The customer should be advised to exclude certain workflows to reduce use.
  B. High network exempt use could be a problem.
  C. You should immediately investigate further bygathering perfstat data and opening a support case.
  D. The CPU Is not a first-order monitoring metric for ONTAP.
  C. You should immediately investigate further bygathering perfstat data and opening a support case.

  ---

  Explanation/Reference:

• Question 48:

  After a motherboard replacement on a NetApp AFF A300 in a SAN environment, the customer states that ports 0e and 0f are unable toconnect to the fabric. The ports report "offline".

  What would you examine first to troubleshoot the issue?

  A. vserver fcp wwpn-alias show command output
  B. system node hardware unified-connect show command output
  C. storage port show command output
  D. vserver fcp interface show command output
  C. storage port show command output

• Question 49:

  When an administrator tries to create a share for an existing volume named voll, the process fails with an error.

  

  Referring to the exhibit, what Is the reason for the error?

  A. The volume must have a type of DP.
  B. The volume has not beenmounted.
  C. The CIFS service is not authenticating properly with the domain controller.
  D. The CIFS service is not in workgroup mode.
  B. The volume has not beenmounted.

• Question 50:

  Your customer complains that u host will constantly report losing a connection to the iSCSl target and then report that the session was reestablished.

  

  As shown in the exhibit, what is a cause of this flapping?

  A. A host with an IP address of 172.20.10.80 and a second host with an IP address of 10.10.20.60 have the same IQN.
  B. A host with an IP address of 172.20.10.80 and a secondhost with an IP address of 10.10.20.60 are in different initiator groups.
  C. A host with an IP address of 172.20.10.80 and a second host with an IP address of 10.10.20.60 are accessing the same LUN.
  D. A host with an IP address of 172.20.10.80 and a secondIP address of 10.10.20.60 is accessing different LUNs.
  C. A host with an IP address of 172.20.10.80 and a second host with an IP address of 10.10.20.60 are accessing the same LUN.