NetApp NS0-593 Online Practice Questions and Exam Preparation

NetApp NS0-593 Online Questions & Answers

• Question 11:

  A customer's storage administrator Informs you about the deactivated Automatic Switchover (AUSO) feature on their MetroCluster IP environment. What Information would you tell your customer in this scenario?

  A. The AUSO feature cannot be activated due to a non-mirrored aggregate.
  B. The AUSO feature is not available in Metrocluster IP installations by design.
  C. A faulty link automatically deactivated the AUSO feature.
  D. This is a configuration failure, you can activate that feature for the customer.
  A. The AUSO feature cannot be activated due to a non-mirrored aggregate.

• Question 12:

  Which two automation methods does NetApp ONTAP Select support? (Choose two.)

  A. REST
  B. Anslble
  C. Docker
  D. PHP
  A. REST
  B. Anslble

• Question 13:

  Referring to the exhibit, from which delay center is most of the latency for voll?

  

  A. Disk
  B. Network
  C. Data
  D. NVRAM
  B. Network

  ---

  Explanation/Reference:

• Question 14:

  You have a new VMware vSphere cluster with ESXI 7.0U2 hosts. The hosts are connected to a 4-node AFF A400 NetApp ONTAP9.8 cluster with FC LUNs. You have a requirement to identify and follow I/Os from each VM on the shared FC LUN-backed datastores for troubleshooting purposes.

  In this scenario, which VMware feature Is supported by ONTAP software to accomplish this task?

  A. Network I/O Control (NIOC)
  B. Virtual machine ID (VMID)
  C. Storage I/O Control (SIOC)
  D. vSphere Cluster Services (vCLS)
  D. vSphere Cluster Services (vCLS)

• Question 15:

  You are attempting to connect a NetApp ONTAP cluster to a very complex network that requires LIFs to fail over across subnets. How would youaccomplish this task?

  A. Configure an equal number of UFs on each subnet.
  B. Configure VIP LIFs using OSPF.
  C. Configure VIP LIFs using BGP.
  D. Configure a I IF failover policy for each subnet inside a single broadcast domain.
  C. Configure VIP LIFs using BGP.

• Question 16:

  When you review performance data for a NetApp ONTAP cluster node, there are back-to- back (B2B) type consistency points (CPs) found occurring onthe loot aggregate.

  In this scenario, how will performance of the client operations on the data aggregates be affected?

  A. During B2B processing, clients will be unable to write data.
  B. Data aggregates will not be affected by B2B processing on another aggregate.
  C. During B2B processing, all I/O to the node is stopped.
  D. During B2B processing, clients will be unable to read data.
  B. Data aggregates will not be affected by B2B processing on another aggregate.

• Question 17:

  The motherboard of Node-01 is being replaced. To perform this task, a takeover was Initiated from Node-02. Node-02 panics showing the string below.

  PANIC; Permanent errors on all HA mailbox disks (while marshalling header) in SKprocess fnmbx_instanceWorker on release 9.5P8 (C)

  What has happened in this situation?

  A. While in maintenance mode, the sldiag device show command was executed.
  B. While in maintenance mode, the fcadmin device_map command was executed.
  C. While in maintenance mode, the HA_config show command was executed.
  D. While in maintenance mode, the mailbox destroy local command was executed.
  B. While in maintenance mode, the fcadmin device_map command was executed.

• Question 18:

  You created a new NetApp ONTAP FlexGroup volume spanning six nodes and 12 aggregates with a total size of 4 TB. You added millions of files to the FlexGroup volume with a flat directory structure totaling 2 TB, and you receive anout of apace error message on your host.

  What would cause this error?

  A. The maximum number of volume constituents has been reached in the ONTAP software.
  B. All constituent volumes are full.
  C. The inode limit is exceeded in the ONTAP software.
  D. The maxdirsize Is exceeded in the ONTAP software.
  C. The inode limit is exceeded in the ONTAP software.

• Question 19:

  A customer calls you to troubleshoot a network issue. The customer wants to create a packet trace for allclients on the 192.168.9.0/24 subnet.

  

  Referring to the exhibit, on which interface do you have to run the packet trace?

  A. a0a-322
  B. e2a-100
  C. e2a-1092
  D. a0a-456
  C. e2a-1092

• Question 20:

  After a normal power down of both nodes forbuilding maintenance, Node01 of a 2-node cluster cannot be powered back up; however, all disk shelves are powered. Which action should be performed to bring the cluster online and allow Node02 to serve data?

  A. Recreate the cluster with the system configuration recovery cluster recreate -from node command.
  B. Reboot the node With the system node reboot -node Node02 -bypass-optimization true command.
  C. Perform a takeover with the storage failover takeover -ofnode Node01 -option forcecommand.
  D. Reinitialize the cluster with option 4a from the boot menu.
  A. Recreate the cluster with the system configuration recovery cluster recreate -from node command.