NetApp NS0-504 Online Practice Questions and Exam Preparation

NetApp NS0-504 Online Questions & Answers

• Question 281:

  What is the name of the SAN replicated database ring in Data ONTAP Cluster-Mode 8.1 and later?

  A. None of the above. The SAN protocol does not have a database replication ring.
  B. LUN Configuration and Operation Manager daemon (LCOMd)
  C. Block Configuration and Operation Manager daemon (BCOMd)
  D. SAN Configuration and Operation Manager daemon (SCOMd)
  E. FC Configuration and Operation Manager daemon (FCOMd)
  C. Block Configuration and Operation Manager daemon (BCOMd)

• Question 282:

  Which action will cause a currently in-sync SnapMirror relationship to fail out of sync?

  A. Running snapmirroe update on the source storage system.
  B. Running snapmirror release on the source storage system.
  C. Modifying the /etc/snapmirror.conf file for the relationship on the source storage system
  D. Modifying the /etc/snapmirror.conf file for the relationship on the destination storage system.
  D. Modifying the /etc/snapmirror.conf file for the relationship on the destination storage system.

• Question 283:

  Which set of protocols provide block-level access to NetApp storage?

  A. SNA and RPC
  B. iSCSI and FCP
  C. HTTP and FTP
  D. CIFS and NFS
  B. iSCSI and FCP

• Question 284:

  Which two will allow you to read and analyze a packet trace file generated by the storage system? (Choose two)

  A. WireShark
  B. Pktt
  C. Netmon
  D. Eternal View
  A. WireShark
  C. Netmon

• Question 285:

  What does it signify if the disks are "not owned" in a FAS2020 system?

  A. The disks are mailbox disks.
  B. The disks are spare disks.
  C. The disks are data disks.
  D. The disks are not used.
  D. The disks are not used.

• Question 286:

  On a Cisco Nexus 5000 series switch, what must occur before the FCoE initiators and FCoE targets can discover each other?

  A. Port logoff
  B. Nameserver erase
  C. Fabric logoff
  D. Proper zoning
  A. Port logoff

• Question 287:

  Using the output below, a co-worker determined that these are type "Solaris" LUNs. What would your determination be? lun show -m LUN pathMapped to LUN ID

  /vol/vol1/lun0 solaris-igroup0 0 /vol/vol1/lun1 solaris-igroup1 0 /vol/vol1/qtree1/lun2 solaris-igroup2 0 /vol/vol1/qtree1/lun3 solaris-igroup3 0

  A. These are type "Solaris" LUNs.
  B. Not enough information is given here. Run the lun map command to get the information requested.
  C. Not enough information is given here. Run the lun show -v command to get the information requested.
  D. Not enough information is given here. Run the lun status command to get the information requested.
  C. Not enough information is given here. Run the lun show -v command to get the information requested.

• Question 288:

  What information is replicated across the SAN replicated database ring in Data ONTAP Cluster- Mode 8.1 and later?

  A. LUN data
  B. SCSI commands
  C. FC connection information
  D. Igroups, port sets, and LUN mappings
  D. Igroups, port sets, and LUN mappings

• Question 289:

  Which utility on Windows 2003 and Windows 2008 can be used to collect information about firmware and driver versions for an Emulex LP1xxxx/LPe1xxx HBA?

  A. EMutil
  B. SANutil
  C. fcp config
  D. SANsurfer
  E. HBAnywhere
  E. HBAnywhere

• Question 290:

  What happens when a node loses SAN protocol quorum? (Choose two.)

  A. The node's HA partner initiates a takeover of the out of quorum node.
  B. The node continues serving data via SAN protocols, but only over direct paths.
  C. The node stops serving data via SAN protocols completely until it is rebooted.
  D. The node stops serving data via SAN protocols until the node quorum reinitialize command is executed.
  B. The node continues serving data via SAN protocols, but only over direct paths.
  D. The node stops serving data via SAN protocols until the node quorum reinitialize command is executed.