NetApp NS0-504 Online Practice Questions and Exam Preparation

NetApp NS0-504 Online Questions & Answers

• Question 171:

  When building your implementation plan, providing dual power for all systems is critical. Which three actions should be mandated? (Choose three.)

  A. Dual power supplies should be placed in all equipment.
  B. Dual power feeds should be run to all equipment.
  C. Power feeds should be connected to the closest available outlet inside the cabinet.
  D. Power feeds should be connected to separate circuits on the same data center PDU.
  E. Power feeds should be connected to separate outlets connected to two separate PDUs.
  A. Dual power supplies should be placed in all equipment.
  B. Dual power feeds should be run to all equipment.
  E. Power feeds should be connected to separate outlets connected to two separate PDUs.

• Question 172:

  Which command do you use on a Brocade FC switch to view all defined zone configuration information?

  A. cfgActvShow
  B. show zone
  C. cfgshow
  D. switchshow
  A. cfgActvShow

• Question 173:

  Which option needs to be set on a volume to guarantee that it cannot be affected by other volumes?

  A. None
  B. Volume
  C. Space Reserved
  D. Reservation Enabled
  B. Volume

• Question 174:

  Five minutes ago, you performed a single file SnapRestore on a large NFS file. 40% of your NFS users are now complaining about getting "stale file handles" for the file. Which is the most likely cause of this problem, and the best procedure to correct it?

  A. This might be due to an NFS storage system and client mismatch. Check to see that these users have the same version of the NFS client that existed at the time the snapshot was taken.
  B. NFS users why try to access a reverted file without first reopening it might get a "stale file handle" error message. Have the users try to reopen the file and see if the problem is resolved.
  C. After a single file SnapRestore, NFS users have to reboot their systems. Have them reboot their systems.
  D. These users are on a different subnet from the others. Start troubleshooting by checking their subnet.
  B. NFS users why try to access a reverted file without first reopening it might get a "stale file handle" error message. Have the users try to reopen the file and see if the problem is resolved.

• Question 175:

  To restore a qtree protected with SnapVault from the secondary storage system to the primary storage system, you can ______________. (Choose two.)

  A. restore to a non existing qtree with DOT 7. 2
  B. add the new qtree to the primary storage system with DOT 7.2
  C. overwrite the existing qtree on the primary storage system with DOT 7.3
  D. delete the existing qtree from the secondary storage system with DOT 7.3
  A. restore to a non existing qtree with DOT 7. 2
  C. overwrite the existing qtree on the primary storage system with DOT 7.3

• Question 176:

  When adding nodes to a cluster in Data ONTAP 8.1.1 Cluster Mode, you must observe which two limitations? (Choose two.)

  A. All nodes in a cluster must have the same number of Fibre Channel target ports.
  B. All nodes in a cluster must have the same amount of storage capacity.
  C. All nodes in a cluster must have redundant connections to the cluster network
  D. All nodes in a cluster must be of the same storage controller model.
  E. Nodes may only be added in HA pairs.
  C. All nodes in a cluster must have redundant connections to the cluster network
  E. Nodes may only be added in HA pairs.

• Question 177:

  Which type of VLAN protects against media access control (MAC) spoofing?

  A. Static
  B. Dynamic
  C. NPIV
  D. VSAN
  B. Dynamic

• Question 178:

  Which four FC fabric topologies does NetApp support? (Choose four.)

  A. four FC switches with multiple Inter-Switch Links (ISLs) between each pair of switches
  B. ten FC switches per fabric, daisy chained with a single ISL between switches
  C. four FC switches with multiple ISLs between ALL switches
  D. eight FC switches with no more than a single ISL between switches in a cascade topology
  E. dual FC switches with no ISLs
  F. a single FC switch
  G. a switched fabric that has 65537 ports
  A. four FC switches with multiple Inter-Switch Links (ISLs) between each pair of switches
  C. four FC switches with multiple ISLs between ALL switches
  E. dual FC switches with no ISLs
  F. a single FC switch

• Question 179:

  When creating a LUN, you use the LUN's OS type to specify which two? (Choose two)

  A. The LUN's MPIO policy
  B. Data offset for I/O alignment
  C. Whether the LUN is space reserved
  D. The LUN's maximum size
  E. The LUN's geometry
  F. Which protocols can be used to access the LUN
  D. The LUN's maximum size
  E. The LUN's geometry

• Question 180:

  Click the Exhibit button.

  

  A Solaris 10 host with VERITAS Storage Foundation 4.1 is FCP attached to a FAS3140 high availability storage system running single image cfmode. Using the diagram shown, which ports will be considered active by VERITAS DMP using the NetApp ASL to a LUN on controller 1 mapped to host 1?

  A. Port 0b on controller 1 only
  B. Port 0d on controller 1 only
  C. Port 0b and 0d on controller 1 only
  D. Ports 0b and 0d on both controller 1 and controller 2
  C. Port 0b and 0d on controller 1 only