NetApp NS0-193 Online Practice Questions and Exam Preparation

NetApp NS0-193 Online Questions & Answers

• Question 51:

  Click the Exhibit button.

  

  A customer noticed that data in volume Snapshot copies was using 200% of the total space allocated to the Snapshot reserve. The configured value of the Snapshot reserve is 10%. The customer wants to maintain the current number of Snapshot copies consuming below 100% of the Snapshot reserve.

  Referring to the exhibit, which action would satisfy the customer's requirement?

  A. Increase the volume size by 50 GB.
  B. Set the volume's fractional reserve to 0.
  C. Move the Snapshot copies to another volume.
  D. Set the Snapshot reserve to 25%.
  D. Set the Snapshot reserve to 25%.

• Question 52:

  Which two SVMs would benefit from a load-sharing mirror? (Choose two.)

  A. An SVM that is configured for FCP.
  B. An SVM that is configured for CIFS.
  C. An SVM that is configured for NFS.
  D. An SVM that is configured for iSCSI.
  B. An SVM that is configured for CIFS.
  C. An SVM that is configured for NFS.

  ---

  Reference: https://library.netapp.com/ecmdocs/ECMP1368017/html/GUID-4931A901-D6D0-458B-8D3A-A92427FDD8B8.html

• Question 53:

  A coworker notices an "Unsynchronized Log" message on an AFF A700 controller. You suspect that the problem might be with the HA interconnect. In this scenario, which two commands would you use to provide additional information? (Choose two.)

  A. Use the event log show command.
  B. Use the system cluster-switch show command.
  C. Use the storage failover show command.
  D. Use the storage adapter show command.
  A. Use the event log show command.
  C. Use the storage failover show command.

• Question 54:

  Click the Exhibit button.

  

  Your database administrator is complaining of slow read and write performance.

  Referring to the exhibit, which action would be taken to improve performance for both reads and writes?

  A. Replace the node's NVRAM.
  B. Move the workload to an SSD aggregate.
  C. Apply a QoS minimum policy to the csdata-wid1234 workload.
  D. Balance the network load among the cluster nodes.
  B. Move the workload to an SSD aggregate.

• Question 55:

  When troubleshooting an I/O module (IOM), which action should you perform before replacing it?

  A. Swap IOM-A with IOM-B in the shelf.
  B. Reseat the IOM.
  C. Reboot the node.
  D. Power cycle the shelf.
  D. Power cycle the shelf.

• Question 56:

  What is NVRAM used for when a node performs a takeover?

  A. The NVRAM contains all the outstanding write operations that were pending to the node that was taken over.
  B. The NVRAM contains only the metadata operations that were pending to the node that was taken over.
  C. The NVRAM contains only the Snapshot copies that were pending to the node that was taken over.
  D. The NVRAM contains all the outstanding read operations that were pending to the node that was taken over.
  D. The NVRAM contains all the outstanding read operations that were pending to the node that was taken over.

• Question 57:

  Click the Exhibit button.

  

  Your SAN customer is experiencing database latency, that is backed by an AFF A300 cluster. The LUNs are connected using a 16Gb fabric.

  Referring to the exhibit, which two steps would you take to determine the issue? (Choose two.)

  A. Inspect the controller for CPU utilization.
  B. Determine if there are issues on the hosts.
  C. Investigate the switch for underruns or other problems.
  D. Examine the controller for faults with the SSDs.
  A. Inspect the controller for CPU utilization.
  D. Examine the controller for faults with the SSDs.

• Question 58:

  You deploy an AFF storage system that is running ONTAP 9.5.

  In this scenario, which three features are enabled by default? (Choose three.)

  A. inline adaptive compression
  B. inline secondary compression
  C. postprocess compression
  D. aggregate-level deduplication
  E. inline data compaction
  A. inline adaptive compression
  B. inline secondary compression
  E. inline data compaction

• Question 59:

  Which three statements are true about failover groups? (Choose three.)

  A. Failover groups are not used by SAN LIFs.
  B. A single port cannot reside in multiple failover groups.
  C. When a broadcast domain is created, a failover group is automatically created.
  D. All of the ports in a failover group must belong to the same broadcast domain.
  E. All of the ports in a failover group must be the same speed.
  A. Failover groups are not used by SAN LIFs.
  C. When a broadcast domain is created, a failover group is automatically created.
  D. All of the ports in a failover group must belong to the same broadcast domain.

  ---

  Reference: https://docs.netapp.com/ontap-9/index.jsp?topic=%2Fcom.netapp.doc.dot-cm-nmg%2FGUID-92E49E15-BE9A-4C5D-ADCA-E606802CBFD4.html

• Question 60:

  An administrator wants to perform a patch upgrade on their ONTAP 9.5 HA cluster. What are two ways to accomplish this task? (Choose two.)

  A. Use the netboot procedure.
  B. Use the automated nondisruptive upgrade (ANDU) process in the Cluster CLI.
  C. Use the automated nondisruptive upgrade (ANDU) process from OnCommand System Manager.
  D. Use the storage disk updatefirmware command.
  B. Use the automated nondisruptive upgrade (ANDU) process in the Cluster CLI.
  C. Use the automated nondisruptive upgrade (ANDU) process from OnCommand System Manager.

  ---

  Reference: https://docs.netapp.com/ontap-9/index.jsp?topic=%2Fcom.netapp.doc.dot-cm-ug-rdg%2FGUID-590B351F-BDDF-41B5-B0F1-391BEC7542E1.html