NetApp NS0-192 Online Practice Questions and Exam Preparation

NetApp NS0-192 Online Questions & Answers

• Question 1:

  You are adding an additional node to a single-node cluster.

  Which of the actions should be performed after this upgrade? (Choose two.)

  A. Verify that HA is enabled.
  B. Verify that epsilon is not assigned.
  C. Verify that epsilon is assigned.
  D. Verify that HA is disabled.
  C. Verify that epsilon is assigned.
  D. Verify that HA is disabled.

• Question 2:

  A customer recently experienced a panic on one node of an ONTAP cluster. Prior to performing the giveback, they want to know what caused the panic. You request data from the customer to assist Support in determining the cause of the panic.

  What information should be requested in this situation? (Choose three.)

  A. panic string
  B. Perfstat
  C. core dump
  D. message logs
  E. packet trace
  A. panic string
  C. core dump
  D. message logs

• Question 3:

  A customer performed maintenance last weekend and power cycled both FAS8060 nodes of a 2-node ONTAP 9.2 cluster. The customer is concerned about port errors seen from the system ha interconnect port show command output. Which two steps would you perform in troubleshooting this condition? (Choose two.)

  A. Use the system ha interconnect link off/on command to manually reset the HA interconnect Link 0 and Link 1 on both nodes.
  B. Perform a takeover/giveback of both nodes.
  C. reset the counters using the system ha interconnect statistics clear-port command.
  D. Use the system ha interconnect flush command to manually reset the HA interconnect Link 0 and Link 1 on both nodes.
  A. Use the system ha interconnect link off/on command to manually reset the HA interconnect Link 0 and Link 1 on both nodes.
  B. Perform a takeover/giveback of both nodes.

• Question 4:

  A customer has a company-wide power outage scheduled and needs to gracefully power off a 2-node cluster. In this scenario, which of two steps should be performed? (Choose two.)

  A. Use the halt -node * -skip-lif-migration-before-shutdown true -inhibit-takeover true command.
  B. Invoke an AutoSupport message to indicate a planned maintenance time.
  C. Use OnCommand System Manager to halt the controllers.
  D. Use the halt -node * command.
  A. Use the halt -node * -skip-lif-migration-before-shutdown true -inhibit-takeover true command.
  D. Use the halt -node * command.

• Question 5:

  What is the proper command to start a packet trace in ONTAP 9.3?

  A. system node run -node * pktt
  B. network ping
  C. network traceroute
  D. network tcpdump start
  D. network tcpdump start

• Question 6:

  A customer has an SVM with an SSD aggregate that is reaching capacity. They want to move the data to another SVM with attached SATA drives. Which two ONTAP features will accomplish this task? (Choose two.)

  A. volume copy
  B. volume move
  C. volume rehost
  D. volume relocate
  B. volume move
  C. volume rehost

• Question 7:

  Click the Exhibit button.

  

  You are creating a new LIF on a new SVM named "bravo-fs2". The cluster is being used in a multitenancy environment, and the bravo tenant has VLAN 105 assigned to it. You receive the error shown in the exhibit when you are creating the LIF. You have verified that the IP address is correct and the existing IP addresses that are already configured are also correct.

  Referring to the exhibit, why is this error occurring?

  A. Two NetApp LIFs cannot have the same IP address assigned.
  B. Another device on VLAN 105 already has the IP address.
  C. The network switch VLAN configuration is incorrect.
  D. Using the same IP address on two LIFs requires different IPspaces.
  C. The network switch VLAN configuration is incorrect.

• Question 8:

  A customer using a FAS9000 needs to perform a takeover, but their system indicates that a takeover is not possible. You have the customer execute the storage failover show -instance -node nodeb command with the resulting message, "Takeover Not Possible: NVRAM log not synchronized".

  In this scenario, what would you do to solve the problem?

  A. Verify that the interconnect cables are connected correctly between the nodes and verify the interconnect links status by using the cluster show -instance command.
  B. Reboot each node to correct the problem, and then rerun the command to verify that the problem has corrected itself. If the problem still exists, reseat the controller module.
  C. Verify that the interconnect cables are connected correctly between the nodes and verify the interconnect links status by using the storage failover show -instance command.
  D. Power off the node manually to force a takeover and reseat the controller module. When the system comes back up, rerun the command to see if it the problem still exists.
  C. Verify that the interconnect cables are connected correctly between the nodes and verify the interconnect links status by using the storage failover show -instance command.

• Question 9:

  Click the Exhibit button.

  

  You are attempting a storage giveback, but the process does not finish successfully. Referring to the exhibit, what is the problem?

  A. An aggregate has failed.
  B. There are active CIFS or NFSv4 connections.
  C. Node cluster-02 was not ready for giveback.
  D. The giveback failed on the node root aggregate.
  D. The giveback failed on the node root aggregate.

• Question 10:

  A manager wants a volume to have a guaranteed 300 MB/s of read performance. You explain that you cannot do this on FAS storage running ONTAP 9.3 backed by 10,000 RPM disks. What is the reason for this response?

  A. Throughput floors apply to only iSCSI access.
  B. Throughput floors can only guarantee up to 125 MB/s.
  C. Throughput floors require a license.
  D. Throughput floors require AFF.
  D. Throughput floors require AFF.