NetApp NS0-184 Online Practice Questions and Exam Preparation

NetApp NS0-184 Online Questions & Answers

• Question 1:

  You use the system health subsystem show command to troubleshoot your newly installed ONTAP cluster. In this scenario, which two health outputs would this command show you? (Choose two.)

  A. data switch cabling
  B. cluster switch cabling
  C. shelf connectivity
  D. node CPU utilization
  C. shelf connectivity
  D. node CPU utilization

  ---

  Reference: https://www.doc-developpement-durable.org/file/Projets-informatiques/cours-and-manuels-informatiques/Netapp/Data%20ONTAP%208.0%207-Mode%20System%20Administration%20Guide.pdf

• Question 2:

  Click the Exhibit button.

  

  Referring to the exhibit, what information is forwarded to syslog after you enter the scripted install commands? (Choose two.)

  A. command history
  B. EMS messages
  C. AutoSupport messages
  D. SNMP traps
  A. command history
  C. AutoSupport messages

  ---

  Reference: https://www.netapp.com/media/10674-tr4569.pdf

• Question 3:

  Click the Exhibit button.

  

  You are installing a 2-node AFF A400 switchless cluster. You have cabled the management network to the e0M port. NetApp also recommends cabling to a redundant management network switch. Referring to the exhibit, to which port should the redundant management network be cabled?

  A. 3
  B. 2
  C. 1
  D. 4
  D. 4

• Question 4:

  After completing a technology refresh, you need to schedule a knowledge transfer with a customer. The customer asks you to address a number of topics during the meeting. In this scenario, which two topics would be appropriate to address? (Choose two.)

  A. performing database application data migrations
  B. logging the customer support calls
  C. accessing internal NetApp KB articles
  D. registering for access to the NetApp Support site
  A. performing database application data migrations
  D. registering for access to the NetApp Support site

• Question 5:

  In an ONTAP switched cluster, which three types of traffic travels over the cluster network? (Choose three.)

  A. intercluster SnapMirror
  B. intracluster SnapMirror
  C. Epsilon voting
  D. cluster database replication
  E. remote cluster peering
  A. intercluster SnapMirror
  D. cluster database replication
  E. remote cluster peering

• Question 6:

  You are installing a new ONTAP 9.7 cluster by following the installation and setup poster. You are ready to complete the initial cluster setup. You have connected your laptop to the management switch. However, when browsing the network, you are unable to discover the ONTAP controllers.

  Which statement explains this behavior?

  A. You do not have network discovery enabled.
  B. You do not have a static IP address.
  C. You do not have IPv6 configuration set.
  D. You do not have a default gateway set.
  D. You do not have a default gateway set.

• Question 7:

  You have just racked a new 6-node switched cluster with ONTAP 9.7. You need to configure the cluster switches. In this scenario, which two elements would be used to complete the configuration? (Choose two.)

  A. SFP+ port
  B. rlogin
  C. SSH
  D. serial port
  C. SSH
  D. serial port

• Question 8:

  Click the Exhibit button.

  

  You are adding new DS224C shelves in a new stack to your cluster with FAS8060 controllers running ONTAP 9.7.

  Referring to the exhibit, which two actions should be performed to the cluster before installing the new shelves? (Choose two.)

  A. Move the SAS cables to a new stack.
  B. Enable in-band ACP.
  C. Remove the Ethernet cables.
  D. Disable out-of-band ACP.
  A. Move the SAS cables to a new stack.
  D. Disable out-of-band ACP.

• Question 9:

  What are two ways to identify an AFF All SAN Array system? (Choose two.)

  A. View the ONTAP System Manager system nodes.
  B. View the ONTAP System Manager cluster settings.
  C. Use the cluster image show CLI command.
  D. Use the san config show CLI command.
  A. View the ONTAP System Manager system nodes.
  D. Use the san config show CLI command.

  ---

  Ways to identify an ASA system You can identify an ASA system using ONTAP System Manager or using the ONTAP command line interface (CLI). From the ONTAP System Manager dashboard, you can click on the system nodes. The personality type is displayed as "ASA" for ASA systems. From the CLI, you can use san config show command. The ASA value returns as true for ASA systems

• Question 10:

  Click the Exhibit button.

  

  You are setting up a new AFF A700 into a new rack at a customer's site. The customer asks you to plan for simplified future growth. Referring to the exhibit, how would you satisfy this requirement?

  A. Option 4
  B. Option 2
  C. Option 3
  D. Option 1
  B. Option 2