NetApp NS0-181 Online Practice Questions and Exam Preparation

NetApp NS0-181 Online Questions & Answers

• Question 41:

  Click the Exhibit button.

  

  You are setting up a new AFF A700 into a new rack at a customer's site. The customer asks you to plan for simplified future growth. Referring to the exhibit, how would you satisfy this requirement?

  A. Option 4
  B. Option 2
  C. Option 3
  D. Option 1
  B. Option 2

• Question 42:

  You need to install a cluster with a FAS2720 HA pair and a FAS8300 HA pair.

  Which NetApp tool will verify which cluster interconnect switches support this configuration?

  A. Active IQ Config Advisor
  B. Interoperability Matrix Tool (IMT)
  C. Hardware Universe (HWU)
  D. mysupport.netapp.com site
  C. Hardware Universe (HWU)

  ---

  Explanation/Reference:

  Reference: https://www.netapp.com/media/12424-tr4036.pdf

• Question 43:

  Click the Exhibit button.

  

  You are reviewing the setup of a recently installed FAS9000 switched cluster. As shown in the exhibit, the cluster interconnects are connected to a pair of Cisco Nexus 3132Q-V 40 Gb ports. For a high availability, which ports should swap Ethernet cables?

  A. Swap node1:e8a and node2:e4a.
  B. Swap node1:e4a and node1:e8a.
  C. Swap node2:e4a and node2:e8a.
  D. Swap node1:e4a and node2:e4b.
  C. Swap node2:e4a and node2:e8a.

• Question 44:

  Which three components are required when setting up a new ONTAP cluster? (Choose three.)

  A. password
  B. cluster management IP
  C. node management IP
  D. Advanced Drive Partitioning
  E. intercluster IP
  B. cluster management IP
  C. node management IP
  E. intercluster IP

  ---

  Explanation/Reference:

  Reference: https://docs.netapp.com/ontap-9/index.jsp?topic=%2Fcom.netapp.doc.dot-cm-nmg%2FGUID-1BA3000D-2243-44E4-98CC-8D42A5C8AF8F.html

• Question 45:

  While installing a new AFF A400 HA pair, you are unable to add an NTP server from another subnet. You are able to ping the NTP server from the new cluster. In this scenario, what are two causes of this problem? (Choose two.)

  A. The admin SVM has the wrong gateway.
  B. A firewall is blocking port 123.
  C. The time skew is too great.
  D. The cluster management LIF needs to be in a different IPspace.
  A. The admin SVM has the wrong gateway.
  D. The cluster management LIF needs to be in a different IPspace.

• Question 46:

  While testing a recently installed FAS8700 cluster, a node fails. You now need to replace the impaired node. In this scenario, which two statements are true? (Choose two.)

  A. You must move the boot device from the impaired node to the replacement node.
  B. The boot device must remain intact and must not be removed from the impaired node.
  C. You can change any drives or disk shelves as part of this replacement procedure.
  D. A controller model of the same type must be used to replace the impaired node.
  A. You must move the boot device from the impaired node to the replacement node.
  D. A controller model of the same type must be used to replace the impaired node.

  ---

  Explanation/Reference:

  Reference: https://library.netapp.com/ecm/ecm_download_file/ECMP1147156 (2)

• Question 47:

  You are installing a new ONTAP 9.7 cluster by following the installation and setup poster. You are ready to complete the initial cluster setup. You have connected your laptop to the management switch. However, when browsing the network, you are unable to discover the ONTAP controllers.

  Which statement explains this behavior?

  A. You do not have network discovery enabled.
  B. You do not have a static IP address.
  C. You do not have IPv6 configuration set.
  D. You do not have a default gateway set.
  D. You do not have a default gateway set.

• Question 48:

  Click the Exhibit button.

  

  You want to add a FAS2750 HA pair to an existing 6-node cluster.

  Referring to the exhibit, which action would you perform to begin adding the node?

  A. Use the back command to begin the Cluster Setup wizard.
  B. Reboot the node and enter maintenance mode and run the Cluster Setup wizard.
  C. Use the node setup wizard and select 0a as the management interface.
  D. Use the exit or quit commands then run the cluster setup command.
  C. Use the node setup wizard and select 0a as the management interface.

  ---

  Explanation/Reference:

  Reference: http://docs.netapp.com/ontap-9/topic/com.netapp.doc.dot-cm-sag/System%20administration.pdf (35)

• Question 49:

  What should you do to change the data protocol of a LIF?

  A. Delete and re-recreate the LIF.
  B. Add the new data protocol to the LIF.
  C. Put the LIF in another broadcast domain.
  D. Shut down the assigned port.
  A. Delete and re-recreate the LIF.

  ---

  Explanation/Reference:

  Reference: https://docs.netapp.com/ontap-9/index.jsp?topic=%2Fcom.netapp.doc.dot-cm-nmg%2FGUID-26EEBB35-4CA6-4814-B819-32DAB46F50E5.html

• Question 50:

  Click the Exhibit button.

  

  You plan to install a new ONTAP cluster at a customer site by using the new ONTAP System Manager 9.7 GUI. Referring to the exhibit, what must you do before you provision initial storage?

  A. Configure cluster LIFs.
  B. Configure protocols.
  C. Configure a remote tier.
  D. Configure aggregates.
  D. Configure aggregates.