NetApp NS0-163 Online Practice Questions and Exam Preparation

NetApp NS0-163 Online Questions & Answers

• Question 21:

  Which is true of the SnapVault backup of NetApp storage system?

  A. The file is the basic unit forSnapVault backup destination.
  B. Theqtree is the basic unit for SnapVault backup destination
  C. The volume is the basic unit ofSnapVault backup destination.
  D. The directory is the basic unit forSnapVault backup destination.
  B. Theqtree is the basic unit for SnapVault backup destination

• Question 22:

  You have connected all cables and disk shelves in a Fabric Attached MetroCluster. Which one of the following commands would you use to verify that disks are connected and have dual paths?

  A. storage show disk-p
  B. sysconfig -v
  C. vol status -r
  D. disk show
  A. storage show disk-p

• Question 23:

  After configuring an ONTAP cluster for SAN access, the administrator is notified that the cluster nodes are connected to separate FC switches.

  Given the following output: What action will correct the redundancy issue?

  

  A. swap cable at node-01 / 1b with cable at node-02 / 1b
  B. swap cable at node-01 / 1a with cable at node-01 / 1d
  C. swap cable at node-01 / 1d with cable at node-02 / 1d
  D. swap cable at node-01 / 1c with cable at node-02 / 1c
  C. swap cable at node-01 / 1d with cable at node-02 / 1d

• Question 24:

  Which command displays the disk ownership for both CPU modules in a FAS270C appliance?

  A. disk show-v
  B. disk display-r
  C. disk own -s
  D. vol status -r
  A. disk show-v

• Question 25:

  Which three are required licenses for Fabric Attached MetroCluster? (Choose 3)

  A. Syncmirror_remote
  B. Syncmirrorocal
  C. Cluster
  D. Cluster remote
  B. Syncmirrorocal
  C. Cluster
  D. Cluster remote

• Question 26:

  If the local node has its FC HBA connected to switch Bank 1, it owns the disks connected to switch bank .

  A. 1
  B. 3
  C. 4
  D. 2
  D. 2

• Question 27:

  Which NetApp solution enables block-level backup and restore from ONTAP to StorageGRID?

  A. FabricPool
  B. Cloud Backup
  C. LockVault
  D. SnapRestore
  B. Cloud Backup

• Question 28:

  Which two choices are used to configure a semi-synchronous SnapMirror relationship? (Choose two.)

  A. throttle
  B. visibility interval
  C. outstanding=3s in DOT 7.2
  D. using option semi-sync in DOT 7.3 and higher
  C. outstanding=3s in DOT 7.2
  D. using option semi-sync in DOT 7.3 and higher

• Question 29:

  After you use SnapRestore to revert a volume to a specific snapshot,....

  A. snapshots that are older than the snapshot you used to revert are deleted.
  B. the storage appliance automatically performs a snapshot for that volume.
  C. snapshots that are more recent than the snapshot you used to revert are deleted.
  D. you must bring the volume back online.
  C. snapshots that are more recent than the snapshot you used to revert are deleted.

• Question 30:

  Which two steps should an administrator take to create a two-node ONTAP Select cluster that spans two data centers and provide automated switchover without any data loss? (Choose two.)

  A. Use ONTAP Mediator service to make sure that a quorum exists for the two nodes
  B. Make sure that the ONTAP Select Deploy VM resides at a third location other than the two data centers
  C. Use ONTAP Select Deploy to install the nodes on the VMware environment
  D. Set up a SnapMirror Synchronous relationship in StrictSync mode to prevent any data loss in case of a failover
  A. Use ONTAP Mediator service to make sure that a quorum exists for the two nodes
  D. Set up a SnapMirror Synchronous relationship in StrictSync mode to prevent any data loss in case of a failover