Nutanix NCM-MCI-5.15 Online Practice Questions and Exam Preparation

Nutanix NCM-MCI-5.15 Online Questions & Answers

• Question 71:

  An administrator needs to initiate a new VDI project within a couple of months. Prism Central reports there are no storage resources to accommodate such workloads.

  The administrator sees many powered-off VMs and has the authority to delete test VMs powered off at least for 30 days. Test VMs belong to the Test category.

  Using Prism Central, which steps are required to identify the correct VMs to be deleted?

  A. Use Capacity Runway to filter by Test and Powered-off VMs
  B. Filter VMs list, choose Test category and Inactive under Efficiency
  C. Create a new Scenario selecting Test VMs. filter by uptime
  D. Create a new Project selecting Test VMs, sorting by power state
  B. Filter VMs list, choose Test category and Inactive under Efficiency

• Question 72:

  An administrator needs to deploy an application with a large amount of data connected via Nutanix Volumes. Which two actions should the administrator take when designing the Volume Group? (Choose two.)

  A. Use multiple subnets for iSCSI traffic
  B. Enable RSS (Receive Side Scaling)
  C. Enable thick provisioning on the Volume Group(s)
  D. Distribute workload across multiple virtual disks
  B. Enable RSS (Receive Side Scaling)
  D. Distribute workload across multiple virtual disks

• Question 73:

  An administrator has a custom backup application that requires a 2TB disk and runs in Windows. Throughput is considerably lower than expected.

  The application was installed on a VM with the following configuration:

  Four vCPUs with one core/vCPU 4GB of Memory One 50GB vDisk for the Windows installation One 2TB vDisk for the application

  What is the recommended configuration change to improve throughput?

  A. Increase the number of cores per vCPU
  B. Increase the vCPUs assigned to the VM
  C. Span the 2TB disk across four vDisks
  D. Add 4GB of memory to the VM
  C. Span the 2TB disk across four vDisks

• Question 74:

  In a Nutanix cluster, a Protection Domain contains 50 entities that are replicated to a remote Single Node Replication Target.

  The current schedule configuration is as follows:

  Repeat every 6 hours

  Local Retention Policy 1 Remote Retention Policy 8 Starting time 12 am

  At 8 am on Monday, the administrator discovers that a protected VM is corrupted. The latest good state was Sunday 2 pm. The administrator needs to maintain current protection. Which strategy should the administrator use to meet these requirements?

  A. From the Remote site, activate the Protection Domain, then re-protect the entity.
  B. From the Remote site, restore the VM from the local snapshot by selecting the correct snapshot
  C. From the local site, retrieve the correct remote snapshot, then restore the VM locally.
  D. From the local site, restore the VM from the local snapshot by selecting the correct snapshot.
  C. From the local site, retrieve the correct remote snapshot, then restore the VM locally.

• Question 75:

  Refer to the exhibit.

  

  An administrator notices a critical alert on the Metro Availability Protection Domain What is causing this alert?

  A. Metro Availability Protection domain is active on the remote site.
  B. VMware Site Recovery Manager is handling a failover event
  C. Metro Availability did not fail over and caused an outage.
  D. vSphere moved VMs to the remote container, and the VMs must be moved back.
  A. Metro Availability Protection domain is active on the remote site.

• Question 76:

  A Nutanix cluster is deployed with the following configuration:

  Three four-node blocks (A, B, and C)

  All Flash Redundancy Factor 2

  What is the effect of simultaneous disk failures on two nodes located in block A?

  A. VMs are migrated off of the nodes with disk failures.
  B. Each node with a failed disk is marked as degraded.
  C. VM read and write operations continue normally.
  D. VMs on the nodes with failed disks are unable to write data
  C. VM read and write operations continue normally.

• Question 77:

  An administrator receives a notification that storage in a Nutanix cluster is unavailable. The cluster consists of five nodes and is configured with a Fault-Tolerance level of 1 (FT-1).

  Upon investigation, the administrator finds the following:

  All AHV hosts are powered on and the CVMs are running Nodes A, B, and C are connected to one top of rack switch Nodes D and E are connected to a second top of rack switch The cluster status command run on Node A shows that CVM services on nodes D and E are down

  Which issue is causing the storage outage?

  A. The default gateway for the CVMs and AHV hosts is down.
  B. The switch connecting Nodes D and E is down.
  C. The genesis process is down on both Nodes D and E.
  D. Nodes D and E are in maintenance mode.
  B. The switch connecting Nodes D and E is down.

• Question 78:

  An organization is planning an upgrade to AOS 5.15 and wants to understand which cluster products and/or services are supported for physical traffic isolation. Which Nutanix component supports its network traffic being isolated onto its own virtual network?

  A. Volumes
  B. Objects
  C. Containers
  D. Files
  A. Volumes

• Question 79:

  An administrator needs to maximize storage potential in a six-node cluster. The container is configured with the following:

  Post-process compression Capacity deduplication What should the administrator configure to increase space savings?

  A. Erasure coding
  B. Inline compression
  C. Reserve capacity
  D. Cache dedupe
  A. Erasure coding

• Question 80:

  An administrator inherits a new Nutanix environment and logs in to a CVM to check the network configuration. The configuration is as follows: Which action should the administrator take to improve network performance?

  

  A. Configure VLAN tagging both on br0 and br1 and their physical interfaces.
  B. Add eth0 and eth1 to the br0-up bond
  C. Configure balance-sib or balance-tcp mode for br0-up if switch configuration allows
  D. Remove one 10 Gbs interface from br0-up to make sure all 10 Gbs can be used.
  C. Configure balance-sib or balance-tcp mode for br0-up if switch configuration allows