Juniper JN0-361 Online Practice Questions and Exam Preparation

Juniper JN0-361 Online Questions & Answers

• Question 321:

  Which forwarding table designation is used to indicate that load balancing is working correctly?

  A. ucst
  B. msct
  C. ulst
  D. mlst
  C. ulst

• Question 322:

  Which two statements are true about virtual switches? (Choose two.)

  A. Multiple virtual switches share a single MAC table.
  B. Virtual switches contain separate MAC tables.
  C. By default, the direct route associated with a virtual switch's IRB interface is placed in inet.0.
  D. By default, the direct route associated with a virtual switch's IRB interface is placed in the associated virtual switch's routing table.
  B. Virtual switches contain separate MAC tables.
  C. By default, the direct route associated with a virtual switch's IRB interface is placed in inet.0.

• Question 323:

  What is a reason for an OSPF router to display a designated router ID of 0.0.0.0?

  A. The MTU is mismatched.
  B. The subnet mask is mismatched.
  C. The interface type is point-to-point.
  D. The interface type is broadcast.
  C. The interface type is point-to-point.

• Question 324:

  Click the Exhibit.

  

  Referring to the configuration shown in the exhibit, which statement is true?

  A. Traffic destined to address 192.168.5.1 will take next-hop 172.16.1.2.
  B. Traffic destined to address 192.168.5.1 will alternate between next-hops 172.16.1.2 and 172.16.1.3
  C. Traffic destined to address 192.168.5.1 will take next-hop 10.0.1.1.
  D. Traffic destined to address 192.168.5.1 will take next-hop 172.16.1.3.
  D. Traffic destined to address 192.168.5.1 will take next-hop 172.16.1.3.

• Question 325:

  Because of recent network failures, additional circuits have been purchased. In addition, Fast reroute has been configured on critical MPLS LSPs. When the next failure occurs, which two time intervals will affect fast reroute? (Choose two.)

  A. The amount of time required to reroute the traffic onto the detour
  B. The amount of time to detect a link or node failure
  C. The amount of time required to recalculate the best detour
  D. The amount of time it takes to ping the gateway on the detour link
  A. The amount of time required to reroute the traffic onto the detour
  B. The amount of time to detect a link or node failure

• Question 326:

  Which command is used to configure an IRB interface?

  A. set family inet interface irb unit 0 address 192.168.1.1/24
  B. set interface irb unit 0 family inet address 192.168.1.1/24
  C. set interface unit 0 family irb address 192.168.1.1/24
  D. set bridge-domain 0 interface irb address 192.168.1.1/24
  B. set interface irb unit 0 family inet address 192.168.1.1/24

• Question 327:

  You are configuring a trunk interface on an MX Series device and want to ensure that any outgoing frames associated with VLAN 100 are transmitted as untagged frames. Which configuration will achieve this objective?

  A. routing-interface irb.0
  B. vlan-id-list [100]
  C. native-vlan-id 100
  D. vlan-id 100
  A. routing-interface irb.0

• Question 328:

  By default, which router in an MPLS LSP removes the MPLS header?

  A. penultimate router
  B. egress router
  C. ingress router
  D. ultimate router
  A. penultimate router

• Question 329:

  What separates areas in IS-IS?

  A. links
  B. DIS
  C. pseudo nodes
  D. routers
  D. routers

• Question 330:

  In a Junos device functioning as an MPLS transit router, which routing table is used when performing a forwarding lookup for an incoming packet?

  A. mpls.3
  B. inet.0
  C. inet.3
  D. mpls.0
  C. inet.3