Juniper JN0-361 Online Practice Questions and Exam Preparation

Juniper JN0-361 Online Questions & Answers

• Question 311:

  Which packet type does a Junos device use to request up-to-date link-state information?

  A. IIH
  B. LSP
  C. PSNP
  D. CSNP
  C. PSNP

• Question 312:

  You are asked to configure and apply a new routing policy to influence routing advertisements sent to a specific EBGP peer. You must ensure that the new policy does not impact routing advertisements sent to any other peer. In this scenario, which statement is true?

  A. The new policy should be applied as an export policy for the EBGP group in which the peer is defined.
  B. The new policy should be applied as an import policy for the EBGP group in which the peer is defined.
  C. The new policy should be applied as an export policy for the specific EBGP peer.
  D. The new policy should be applied as an import policy for the specific EBGP peer.
  A. The new policy should be applied as an export policy for the EBGP group in which the peer is defined.

• Question 313:

  Click the Exhibit.

  

  You have just configured IS-IS, but the adjacency is not coming up. Referring to the exhibit, what is the cause?

  A. Only one side is configured using the point-to-point parameter.
  B. One router is configured for Level 2 only.
  C. The routers must be in different areas.
  D. The family iso parameters is missing on the interfaces.
  A. Only one side is configured using the point-to-point parameter.

• Question 314:

  Which role does the router ID (RID) have in the BGP route selection process?

  A. The router ID is evaluated immediately after MED to determine route preference
  B. The router ID is evaluated last in the route selection process
  C. The router ID is evaluated after the cluster length and a lower router ID is chosen
  D. The router ID is evaluated after analyzing the IGP metric cost
  C. The router ID is evaluated after the cluster length and a lower router ID is chosen

• Question 315:

  Which two statements are correct regarding LDP-signaled VPLS instances? (Choose two.)

  A. You must enable the Layer 2 VPN signaling NLRI.
  B. You must configure the same VPLS identifier on all peers.
  C. You must define a the same site-identifier value on all peers.
  D. You must define all neighbors using their tunnel end-point IP addresses.
  B. You must configure the same VPLS identifier on all peers.
  D. You must define all neighbors using their tunnel end-point IP addresses.

• Question 316:

  -- Exhibit -

  protocols {

  isis {

  interface lo0.0;

  interface ge-0/0/0.100;

  }

  }

  -- Exhibit -

  Click the Exhibit button.

  Referring to the exhibit, what will be the IS-IS levels enabled on the interface ge-0/0/0.100?

  A. Level 1 only
  B. Level 2 only
  C. Level 1 and Level 2
  D. Level 1, Level 2, and Level 3
  C. Level 1 and Level 2

• Question 317:

  Which protocol do two MC-LAG devices use to exchange control information?

  A. VRRP
  B. BFD
  C. VCCP
  D. ICCP
  D. ICCP

• Question 318:

  Click the Exhibit button.

  

  Which two statements are true regarding the output shown in the exhibit? (Choose two.)

  A. The ge-1/0/0 interface will transmit any outgoing frames associated with VLAN 55 as untagged frames.
  B. The ge-1/0/0 interface will associate any untagged frames that are received with VLAN 56.
  C. The ge-1/0/0 interface will associate any untagged frames that are received with VLAN 55.
  D. The ge-1/0/0 interface will transmit any outgoing frames associated with VLAN 56 as untagged frames.
  B. The ge-1/0/0 interface will associate any untagged frames that are received with VLAN 56.
  D. The ge-1/0/0 interface will transmit any outgoing frames associated with VLAN 56 as untagged frames.

• Question 319:

  -- Exhibit -

  interfaces {

  ge-0/0/0 {

  vlan-tagging;

  unit 100 {

  vlan-id 100;

  family inet {

  address 192.168.100.97/30;

  }

  family iso;

  }

  unit 200 {

  vlan-id 200;

  family inet {

  address 192.168.100.94/30;

  }

  family iso;

  }

  }

  fxp0 {

  description "MGMT INTERFACE - DO NOT DELETE";

  unit 0 {

  family inet {

  address 10.210.10.11/27;

  }

  }

  }

  lo0 {

  unit 0 {

  family inet {

  address 192.168.100.1/32;

  }

  family iso {

  address 49.1111.1921.6801.0001.00;

  }

  }

  }

  }

  protocols {

  isis {

  interface ge-0/0/0.100;

  interface ge-0/0/0.200;

  }

  }

  -- Exhibit -

  Click the Exhibit button.

  An operator is unable to establish any IS-IS adjacencies on a router in the network.

  Based on the configuration shown in the exhibit, what is the problem?

  A. Interface lo0 must be configured in the IS-IS hierarchy.
  B. Each network interface needs a unique family ISO address.
  C. The IS-IS level for an each interface must be specified.
  D. The ISO address for interface lo0 is not in hex format.
  A. Interface lo0 must be configured in the IS-IS hierarchy.

• Question 320:

  You have configured refresh reduction in your RSVP network but you suspect that some of the Junos devices are not correctly operating in that mode. Which operational mode command can be used to view the refresh messages sent and received?

  A. show rsvp interface
  B. show rsvp version
  C. show rsvp neighbor detail
  D. show rsvp session detail
  C. show rsvp neighbor detail