Juniper JN0-130 Online Practice Questions and Exam Preparation

Juniper JN0-130 Online Questions & Answers

• Question 61:

  Which three are correct about L2TP tunnel selection algorithms? (Choose three.)

  A. Failover between preference levels is the default.
  B. One algothrim is failover within a preference level.
  C. Failover across all preference levels is the default.
  D. One algothrim is failover between preference levels.
  E. One algothrim is failover across all preference levels.
  A. Failover between preference levels is the default.
  B. One algothrim is failover within a preference level.
  D. One algothrim is failover between preference levels.

• Question 62:

  Which term describes a group of packets sharing common forwarding characteristics?

  A. common forwarding class
  B. forwarding equivalence class
  C. equivalent class characteristics
  D. forwarding class characteristics
  B. forwarding equivalence class

• Question 63:

  Which control expression must be the last line in all macros?

  C

• Question 64:

  What are two functions that the parameter max-session performs? (Choose two.)

  A. Defines the session limit for the domain.
  B. Defines the session limit for the tunnel instance.
  C. Used to control load balancing between multiple domains.
  D. Used to control load balancing between multiple tunnels for a domain.
  B. Defines the session limit for the tunnel instance.
  D. Used to control load balancing between multiple tunnels for a domain.

• Question 65:

  You are trying to recover from a corrupted flash. Which configuration command configures an IP address of 192.168.1.1/24 on the SRP management interface when the ERX1400 router is at the boot## prompt?

  A. ip address 192.168.1.1/24
  B. ip address 192.168.1.1 subnetmask 24
  C. ip address 192.168.1.1 255.255.255.0
  D. ip address 192.168.1.1 mask 255.255.255.0
  C. ip address 192.168.1.1 255.255.255.0

• Question 66:

  Which CLI command shows whether an L2TP Tunnel Switch profile is applied?

  A. l2tp tunnel test
  B. show subscribers
  C. show aaa domain-map
  D. show l2tp destination profile
  C. show aaa domain-map

• Question 67:

  Which configuration command places interfaces whose IP addresses are between 192.168.0.0 and 192.168.255.255 into OSPF area 0?

  A. network 192.168.0.0 255.255.0.0 area 0.0.0.0
  B. network 192.168.0.0 0.0.255.255 area 0.0.0.0
  C. area 0.0.0.0 network 192.168.0.0 255.255.0.0
  D. area 0.0.0.0 network 192.168.0.0 0.0.255.255
  B. network 192.168.0.0 0.0.255.255 area 0.0.0.0

• Question 68:

  What are the maximum number of classifiers per policy group?

  A. 100
  B. 128
  C. 256
  D. 512
  D. 512

• Question 69:

  What are three ways an IP interface can be assigned to a virtual router in a PPP over ATM environment? (Choose three.)

  A. profile
  B. policy list
  C. domain map
  D. RADIUS VSA
  E. classifier ACL
  A. profile
  C. domain map
  D. RADIUS VSA

• Question 70:

  When does the E-series router start monitoring DHCP traffic using the DHCP External function?

  A. When the discovery packet enters the router from the DHCP client.
  B. Only when the offer packet enters the router from the DHCP server.
  C. When the acknowledge packet enters the router from the DHCP server.
  D. Only when the discovery packet leaves the router going to the DHCP server.
  D. Only when the discovery packet leaves the router going to the DHCP server.