Juniper JN0-130 Online Practice Questions and Exam Preparation

Juniper JN0-130 Online Questions & Answers

• Question 51:

  After evaluating the BGP attributes (AS Path, Local Preference, MED, and Origin) there are four additional route selection techniques used as tie-breakers. In which order are these applied?

  A. prefer EBGP over IBGP, prefer routes from the lowest RID, prefer routes with lowest IGP metric,
  B. prefer routes from the lowest RID, prefer routes with lowest IGP metric, prefer EBGP over IBGP
  C. prefer routes with lowest IGP metric, prefer routes from the lowest RID, prefer EBGP over IBGP,
  D. prefer EBGP over IBGP, prefer routes with lowest IGP metric, prefer routes from the lowest RID
  D. prefer EBGP over IBGP, prefer routes with lowest IGP metric, prefer routes from the lowest RID

• Question 52:

  Which two statements are true regarding EBGP and Confederation BGP? (Choose two.)

  A. EBGP peers advertise MED and change Next Hop.
  B. EBGP peers advertise Local Preference and do NOT change Next Hop.
  C. Confederation BGP peers advertise MED and do NOT change Next Hop.
  D. Confederation BGP peers advertise Local Preference and change Next Hop.
  A. EBGP peers advertise MED and change Next Hop.
  C. Confederation BGP peers advertise MED and do NOT change Next Hop.

• Question 53:

  Which two statements are true about precedence values in policy? (Choose two.)

  A. 1 is the default precedence.
  B. A lower number is preferred.
  C. A higher number is preferred.
  D. 100 is the default precedence.
  B. A lower number is preferred.
  D. 100 is the default precedence.

• Question 54:

  Which message type is used to initiate an RSVP-TE label switched path?

  A. path
  B. resv
  C. setup
  D. session
  A. path

• Question 55:

  Which three statements are correct concerning the CLI commands shown below? (Choose three.) aaa domain isp1.com tunnel 1 address 33.33.33.1

  A. Tunnel 1 is the tunnel identity.
  B. The address is the LNS loopback.
  C. The address is the LAC loopback.
  D. These commands are performed on the LAC.
  E. Tunnel 1 is the first tunnel instance for domain isp1.com.
  B. The address is the LNS loopback.
  D. These commands are performed on the LAC.
  E. Tunnel 1 is the first tunnel instance for domain isp1.com.

• Question 56:

  How can you remove the Privileged Exec password from the router?

  A. Configure erase secret 60 then push the top button on the SRP.
  B. Configure erase secret 300 then push the top button on the SRP.
  C. Configure erase secret 60 then push the bottom button on the SRP.
  D. Configure erase secret 300 then push the bottom button on the SRP.
  C. Configure erase secret 60 then push the bottom button on the SRP.

• Question 57:

  What is the default value of the IS-IS lsp-refresh-interval command?

  A. 60 seconds
  B. 5 minutes
  C. 15 minutes
  D. 30 minutes
  C. 15 minutes

• Question 58:

  Which configuration is correct for a DHCP Relay Proxy?

  A. set dhcp relay 1.1.1.1 set dhcp relay 2.2.2.2 set dhcp relay
  B. set dhcp relay proxy set dhcp relay 1.1.1.1 set dhcp relay 2.2.2.2
  C. set dhcp relay 1.1.1.1 proxy set dhcp relay 2.2.2.2
  D. set dhcp relay 1.1.1.1 set dhcp relay 2.2.2.2 proxy
  C. set dhcp relay 1.1.1.1 proxy set dhcp relay 2.2.2.2

• Question 59:

  What are three valid LDP message types? (Choose three.)

  A. peer discovery
  B. label distribution
  C. path initialization
  D. session management
  E. connection establishment
  A. peer discovery
  B. label distribution
  D. session management

• Question 60:

  Which device is responsible for assigning label values in an MPLS network?

  A. upstream node
  B. originating node
  C. destination node
  D. downstream node
  D. downstream node