Juniper JN0-106 Online Practice Questions and Exam Preparation

Juniper JN0-106 Online Questions & Answers

• Question 171:

  You manage a Junos device with 20 interfaces. Each interface requires the same description and MTU setting.

  Which configuration approach would reduce repetitive commands and ensure consistency?

  A. Use the wildcard delete command to remove duplicate settings.
  B. Configure each interface individually.
  C. Use a configuration group.
  D. Use search and replace to apply settings across interfaces.
  C. Use a configuration group.

• Question 172:

  What are two methods for navigating to configuration mode from an operational mode prompt? (Choose two.)

  A. Use the quit command.
  B. Use the configure command.
  C. Use the exit command.
  D. Use the edit command.
  B. Use the configure command.
  D. Use the edit command.

• Question 173:

  Which two tasks are performed from the Junos operational mode prompt? (Choose two.)

  A. Committing pending configuration changes
  B. Editing a firewall filter term
  C. Displaying the current interface status
  D. Adding a new static route to the candidate configuration
  E. Testing reachability to a remote IP address
  C. Displaying the current interface status
  E. Testing reachability to a remote IP address

• Question 174:

  When troubleshooting a problem, you issue the following commands in sequence:

  1.

  2.

  3.

  4.

  show chassis alarms

  show chassis fpc

  show chassis fpc detail

  show chassis errors fpc-slot 0 In this scenario, what happens when you press the up arrow key twice at the prompt?

  A. The show chassis fpc command is displayed at the prompt.
  B. The show chassis errors fpc-slot 0 command is displayed at the prompt.
  C. The show chassis alarms command is displayed at the prompt.
  D. The show chassis fpc detail command is displayed at the prompt.
  D. The show chassis fpc detail command is displayed at the prompt.

• Question 175:

  An administrator wants to set up a remote user authentication service for the many users that access a Juniper security device.

  In this scenario, what are two supported authentication protocols? (Choose two.)

  A. RADIUS
  B. TACACS+
  C. SHA
  D. IPsec
  A. RADIUS
  B. TACACS+

• Question 176:

  You are reviewing a long command output and need to display only lines that contain a specific keyword.

  Which CLI feature should you use?

  A. Output filtering
  B. Rollback comparison
  C. Candidate configuration
  D. Rescue configuration
  A. Output filtering

• Question 177:

  Referring to the exhibit, which two statements about IPv6 routing are correct? (Choose two.)

  

  A. The router is not learning IPv6 routes from peers.
  B. The router cannot forward traffic to remote IPv6 networks.
  C. Traffic destined for the 2001:db8:22:108::/64 network is forwarded using the ge-0/0/5.0 interface.
  D. The router is connected to the 2001:db8:22:107::/64 network.
  A. The router is not learning IPv6 routes from peers.
  B. The router cannot forward traffic to remote IPv6 networks.

• Question 178:

  Which two statements are correct about logical units? (Choose two.)

  A. A physical interface can host multiple logical units.
  B. Logical units can have multiple IP addresses.
  C. Logical units are used only for management interfaces.
  D. A physical interface can host only one logical unit.
  A. A physical interface can host multiple logical units.
  B. Logical units can have multiple IP addresses.

• Question 179:

  What are two link-state routing protocols? (Choose two.)

  A. RIP
  B. IS-IS
  C. BGP
  D. OSPF
  B. IS-IS
  D. OSPF

• Question 180:

  You are creating a new user account on your Junos device. The user must be able to validate the routing table and interface statistics but should not be able to make any configuration changes.

  In this scenario, which permission flag would satisfy this requirement?

  A. configure
  B. all
  C. view
  D. network
  C. view