HP HPE6-A72 Online Practice Questions and Exam Preparation

HP HPE6-A72 Online Questions & Answers

• Question 1:

  What command will save your configuration on an Aruba AOS-CX switch so that your changes automatically load on next reboot?

  A. copy running-config checkpoint startup-config
  B. copy startup-config running-config
  C. copy running-config initial-checkpoint
  D. copy running-config default
  A. copy running-config checkpoint startup-config

• Question 2:

  Refer to the exhibit.

  

  The command show LLDP neighbor-info gets typed into Access-1. All switches are Aruba OS-CX switches. What is the output of this command?

  

  A. Option A
  B. Option B
  C. Option C
  D. Option D
  D. Option D

• Question 3:

  Which port or ports should be allowed through a firewall so that an AOS-CX switch can act as an SNMP Agent?

  A. UDP 1812 and UDP 1813
  B. UDP 161
  C. TCP 443
  D. UDP 162
  B. UDP 161

• Question 4:

  Refer to the exhibit.

  

  All four switches in the diagram have been configured with the region name "Aruba1".

  What two other MSTP configurations must match for switches within the same MST region? (Choose two.)

  A. MST region type
  B. MST Bridge ID
  C. MST version number
  D. MST revision number
  E. MST VLAN to instance mapping
  D. MST revision number
  E. MST VLAN to instance mapping

• Question 5:

  Which command can be used to find the serial number of an Aruba OS-CX switch?

  A. The command inventory
  B. The command version
  C. The command show running-configuration
  D. The command show system
  D. The command show system

• Question 6:

  Which command will suppress LLDP messages from egressing on a given port while still allowing LLDP to be enabled on the switch?

  A. switch(config-if)# no lldp interface (port) transmit
  B. switch(config-if)# no lldp transmit
  C. switch(config-if)# no lldp receive
  D. switch(config)# no lldp
  B. switch(config-if)# no lldp transmit

• Question 7:

  What command will save your configuration on an Aruba AOS-CX switch so that your changes automatically load on next reboot?

  A. copy running-config checkpoint startup-config
  B. copy startup-config running-config
  C. copy running-config initial-checkpoint
  D. copy running-config default
  A. copy running-config checkpoint startup-config

• Question 8:

  Refer to the exhibit.

  

  Traffic is failing between Core-1 and Host-B. IP addressing has correctly been applied, and all interfaces are attached to the vrf GREEN.

  Which configuration will correct the issue?

  A. Core-2(config)# ip route 0.0.0.0/0 10.1.1.1 vrf GREEN Host-B: assign the default- gateway address 10.1.20.181
  B. Core-1(config)# ip route 10.1.20.0/24 10.1.1.2 vrf GREEN Host-B: assign the default- gateway address 10.1.20.181
  C. Core-1(config)# ip route 10.1.20.0/24 10.1.1.2 vrf GREEN Host-B: assign the default- gateway address 10.1.20.1
  D. Host-B: assign the default-gateway address 10.1.20.181
  B. Core-1(config)# ip route 10.1.20.0/24 10.1.1.2 vrf GREEN Host-B: assign the default- gateway address 10.1.20.181

• Question 9:

  Refer to the exhibit.

  

  What configuration is needed in order for "show LLDP configuration" to show this output?

  A. none; LLDP is enabled by default on Aruba switches
  B. configuring LLDP both globally and on the interfaces
  C. enabling LLDP on the interfaces only
  D. configuring LLDP globally only
  A. none; LLDP is enabled by default on Aruba switches

• Question 10:

  Core#configure terminal Core(config)#vrf Green Core(config-vrf)#exit Core(config)# Core(config)#interface vlan 50 Core(config-if-vlan)#?

  Given the configuration on theCOREswitch shown above, what command would follow to assign the switched virtual interface (SVI) vlan 50 to the VRF created?

  A. Core(config-if-vlan)# vrf attach Green
  B. Core(config-if-vlan)# ip vpn-instance Green
  C. Core(config-if-vlan)# ip vrf forwarding Green
  D. Core(config-if-vlan)# routing-context Green vrf
  A. Core(config-if-vlan)# vrf attach Green