HP HPE2-Z39 Online Practice Questions and Exam Preparation

HP HPE2-Z39 Online Questions & Answers

• Question 21:

  A company needs a modular switch that can be combined with another modular switch into a single logical fabric. Which ArubaOS switch series meets these criteria?

  A. Aruba 2930F Series
  B. Aruba 3800 Series
  C. Aruba 3810 Series
  D. Aruba 5400R Series
  A. Aruba 2930F Series

• Question 22:

  

  An Aruba Instant cluster is added in Aruba AirWave. A network administrator needs to change the cluster management level to Manage Read "Write. The exhibit shows the current status for the cluster. What should the administrator do before changing the management level?

  A. Check the cluster SNMP credentials and resolve the mismatch between the cluster credentials and AirWave credentials.
  B. Verify that the cluster is configured with the same shared key that is configured in the global AirWave settings.
  C. Investigate why the cluster configuration does not match the group configuration template and resolve any issues.
  D. Determine why AirWave cannot contact the cluster and resolve any connectivity issues in the network.
  A. Check the cluster SNMP credentials and resolve the mismatch between the cluster credentials and AirWave credentials.

• Question 23:

  A company wants to use Zero Touch Provisioning (ZTP) to provision new ArubaOS switches. Which AirWave settings must match the switch default SNMP and Telnet/SSH password settings?

  A. Global communication settings
  B. Settings in the device template for the device group to which ZTP switches are assigned
  C. Communication settings for the device group to which ZTP switches are assigned
  D. Credentials in device discovery settings
  D. Credentials in device discovery settings

• Question 24:

  A port on an ArubaOS switch has its default spanning tree settings. When is the port defined as a spanning tree edge port?

  A. when the switch and the connected switch run MSTP but have different region settings
  B. when the switch runs MSTP but the connected switch runs RSTP
  C. when the port fails to receive BPDUs on the port within a set period of time
  D. when the port is part of a VLAN that is dedicated to that port alone
  B. when the switch runs MSTP but the connected switch runs RSTP

• Question 25:

  

  The exhibit shows settings for a WLAN on an Aruba Instant cluster. To which VLAN is wireless user traffic assigned?

  A. to the VLAN defined for wireless users in Aruba AirWave
  B. to the default VLAN on switches connected to the Instant APs
  C. to the default VLAN defined in the System settings in the Instant Ul
  D. to the untagged VLAN on switch ports connected to the Instant APs
  D. to the untagged VLAN on switch ports connected to the Instant APs

• Question 26:

  

  What is the result of this configuration?

  A. The switch only adds the last static route entry to the routing table
  B. All four routes are added to the routing table, but are never used.
  C. The switch load shares connections across the four static next hops.
  D. The switch only adds the last two static route entries to the routing table.
  B. All four routes are added to the routing table, but are never used.

• Question 27:

  A network administrator needs to see the options for the vlan command on an ArubaOS switch. The administrator enters:

  Aruba (config)# vlan?

  No new output displays.

  What should the administrator change to see the vlan command options?

  A. Move to the vlan configuration mode before entering vlan? again.
  B. Use the Tab key instead of ?.
  C. Insert a space in between vlan and ?.
  D. Activate help commands globally before entering vlan? again.
  A. Move to the vlan configuration mode before entering vlan? again.

• Question 28:

  Two ArubaOS switches connect on a VLAN. and both enable OSPF on that VLAN. Which VLAN OSPF setting must match for the switches to become fully adjacent neighbors?

  A. DR priority
  B. area ID
  C. cost
  D. router ID
  D. router ID

• Question 29:

  

  The ArubaOS switches were at default settings. The network administrator configures the VLANs and IP addresses as shown in the exhibit. All inter switch links are untagged for VLAN 1 and tagged for VLANs 11 and 12. There is no additional configuration performed on the switches. The Windows Server and Windows Client are configured to use Switch-1 as their default gateway.

  How does this configuration affect the network topology?

  A. The Windows Server and Windows Client cannot ping each other; IP routing must be enabled on all switches in the topology.
  B. The Windows Server and Windows Client cannot ping each other; the VLANs are tagged incorrectly on one or more ports.
  C. The Windows Server and Windows Client can successfully ping each other.
  D. The Windows Server and Windows Client cannot ping each other; IP routing must be enabled on Switch-1.
  C. The Windows Server and Windows Client can successfully ping each other.

• Question 30:

  What is one requirement to combine Aruba 5400R zl2 Series switches in a Virtual Switching Framework (VSF) fabric?

  A. One of the switches must be an Aruba 5412R switch, white the other member can be any switch in the 5400R series.
  B. Both of the members must have two management modules.
  C. The switches must operate in v3-modute only mode: any modules of an earlier version are automatically disabled.
  D. The interfaces assigned to the VSF link must be pre-configured as part of a link aggregation.
  A. One of the switches must be an Aruba 5412R switch, white the other member can be any switch in the 5400R series.