HP HPE2-T37 Online Practice Questions and Exam Preparation

HP HPE2-T37 Online Questions & Answers

• Question 1:

  Refer to the exhibit.

  

  After adding SAN Manager to HPE OneView. you noticed that all SANs are in the discovered state. How will this affect HPE OneView storage management capabilities?

  A. Snapshot functionality will be limited only to the volumes not using these SANs.
  B. Volume presentation through server profile will work with the discovered state.
  C. Auto-zoning functionality will not work until SANs are associated with networks.
  D. Volume provisioning will only work for arrays that ate accessible through these SANs.
  B. Volume presentation through server profile will work with the discovered state.

• Question 2:

  You have created volumes using array management tools and imported the volumes to HPE OneView. Which statement about these volumes is true?

  A. Imported volumes are treated as private volumes and can be only used as boot volumes
  B. Volumes imported to HPE OneView is managed just like a volume created using HPE OneView
  C. Volumes imported to HPE OneView cannot be removed using the HPE OneView interface
  D. A snapshot for imported volumes can be created only by using array management tools
  D. A snapshot for imported volumes can be created only by using array management tools

• Question 3:

  You want to put two FlexNlCs into a single Link Aggregation Group within a server profile. What Is a prerequisite for this setup?

  A. The sFlow option must be enabled and configured.
  B. Both FlexNlCs must be connected to the same network.
  C. The Compute Module profile must have exactly two connections defined.
  D. An upgrade license must be purchased and deployed.
  B. Both FlexNlCs must be connected to the same network.

• Question 4:

  Which statement about the volume template is true?

  A. Users will be able to change sharing type and volume capacity
  B. A volume created using this template will not support deduplication
  C. A volume created using this template mil not support snapshots
  D. Users will be able to select storage pool during volume creation
  A. Users will be able to change sharing type and volume capacity

• Question 5:

  Which locations are supported for HPE OneView remote scheduled backup? (Choose two.)

  A. SCP
  B. HTTPS
  C. SFTP
  D. HTTP
  E. FTP
  A. SCP
  C. SFTP

• Question 6:

  HOTSPOT

  Click the option that will prevent the appliance from sending any email notifications or forwarding any SNMP traps that are related to the server hardware.

  Hot Area:

  

  

• Question 7:

  After replacing a failed Compute Module, you notice the server profile Is not automatically assigned to the replaced server hardware. What can cause this issue?

  A. IL0 firmware of the replacement server is different than firmware in broken server.
  B. Server profile affinity is configured to Device Day + server hardware.
  C. The enclosure group has to be updated to match the original enclosure group.
  D. The replacement server has more memory or CPUs than broken machine.
  A. IL0 firmware of the replacement server is different than firmware in broken server.

• Question 8:

  You are creating a Logical Interconnect Group for a three-frame HPE Synergy solution with HPE Virtual Connect SE100Gb F32 Modules for Synergy. In which scenario should you set redundancy for master modules to be highly available?

  A. When storm control or loop protection will be enabled for Virtual Connect modules
  B. When each of the frames has two Virtual Connect modules installed
  C. When each Virtual Connect module is installed in different frame
  D. When each Virtual Connect module is installed in different fabric
  A. When storm control or loop protection will be enabled for Virtual Connect modules

• Question 9:

  You originally configured boot mode for HPE ProLiant Gen10 server to `Legacy BIOS' in an HPE OneView server profile and deployed an operating system. A few weeks later, you change the boot mode to the `UEFI optimized' to leverage some features provided by this mode.

  What must you do next?

  A. reset an iLO management processor to activate the new boot mode for the server
  B. reinstall an operating system, as UEFI is using different drive format than Legacy BIOS
  C. reset BIOS settings to the defaults so UEFI settings can be applied
  D. reset BIOS settings to the defaults through the server profile after changing the boot mode
  A. reset an iLO management processor to activate the new boot mode for the server

• Question 10:

  Which types of support dump can be created using HPE OneView? (Select two.)

  A. Enclosure group support dump
  B. Appliance support dump
  C. Firmware deployment support dump
  D. Logical enclosure support dump
  E. Maintenance console support dump
  B. Appliance support dump
  D. Logical enclosure support dump