HP HPE0-S58 Online Practice Questions and Exam Preparation

HP HPE0-S58 Online Questions & Answers

• Question 1:

  A customer using HPE Synergy is unable to access certain VLANs from a single NIC port of a compute module.

  Which configuration option in the server profile needs to be verified to ensure that the server profile has the correct configuration?

  A. multiple Networks are assigned to the connection
  B. multiple VLAN checkbox is selected
  C. VxLAN has not been enabled
  D. assigned Network Set includes all needed VLANs
  D. assigned Network Set includes all needed VLANs

• Question 2:

  An integrator is performing an initial Synergy setup.

  How should the integrator initiate the hardware discovery?

  A. Connect a Serial cable to the front panel, and open a session to the console
  B. Plug in the SUVi cable for the blade server, and attach a monitor
  C. Open a browser, and select Discover in the HPE Synergy Console
  D. Attach a display and a keyboard to the front panel, and click connect
  D. Attach a display and a keyboard to the front panel, and click connect

• Question 3:

  How many redundant fabrics are supported in an HPE Synergy frame?

  B. 2
  C. 3
  D. 4
  C. 3

• Question 4:

  HOTSPOT

  An integrator needs to configure zoned SAS drives from the HPE Synergy D3940 storage module for an HPE SY 480 Gen9 compute module for a new application.

  Click where the integrator should perform the configuration.

  Hot Area:

  

  

• Question 5:

  A customer tries to revert a data volume located on the HPE 3PAR array to a specific snapshot that was taken using HPE Composer, but the process fails. What must an integrator do to fix this problem?

  A. Install the snapshot agent on the operating system to enable online snapshot operations
  B. Select the "Force" checkbox to ignore the warning, and revert to the snapshot because this is a data volume
  C. Navigate to the SSMC and revert to the snapshot using HPE 3PAR tools
  D. Disconnect the volume from the server, then revert to the snapshot and reconnect back to the server
  C. Navigate to the SSMC and revert to the snapshot using HPE 3PAR tools

• Question 6:

  Which HPE Synergy D3940 storage module configuration is valid?

  A. a single RAID set to be shared across the SAS fabric to multiple compute nodes as a virtualization host datastore
  B. maximum of three HPE Synergy D3940 storage modules per frame to be used by any compute module within the management ring
  C. any number of the drives from storage module to be mapped to any single compute node
  D. a pair of disks to house Composer backups and Synergy firmware bundles
  A. a single RAID set to be shared across the SAS fabric to multiple compute nodes as a virtualization host datastore

• Question 7:

  HOTSPOT

  A customer has the following HPE Synergy solution: three Synergy frames two HPE Virtual Connect SE 32Gb Fibre Channel (FC) modules in each time two HPE Virtual Connect SE 40GB F8 modules four HPE Synergy 10Gb Interconnect Link Modules

  Click the menu option the integrator should use to add more uplinks ports from HPE Virtual Connect SE 32 Gb FC modules to SAN uplink set.

  Hot Area:

  

  

• Question 8:

  Refer to the exhibit.

  

  A customer with the design shown needs to perform an in-place upgrade to its environment to scale the two-frame single homed Multimodule Link Aggregation Group (MLAG) configuration to a three-frame configuration. The new frame needs to provide a redundant 20Gb connection for the compute module ports in Fabric 3.

  Which interconnect modules should the integrator use in Frame 3?

  A. HPE Virtual Connect SE 40Gb F8 module in bay 3 and HPE Virtual Connect SE 40Gb F8 Module in bay 6
  B. HPE Synergy 10Gb Interconnect Link Module in bay 3 and HPE Synergy 10Gb Interconnect Link Module in bay 6
  C. HPE Synergy 20Gb Interconnect Link Module in bay 3 and HPE Synergy 20Gb Interconnect Link Module in bay 6
  D. HPE Synergy 20Gb Interconnect Link Module in bay 3 and HPE Synergy 10Gb Interconnect Link Module in bay 6
  B. HPE Synergy 10Gb Interconnect Link Module in bay 3 and HPE Synergy 10Gb Interconnect Link Module in bay 6

• Question 9:

  An integrator needs to configure a set of networks for Synergy compute nodes to send data to devices outside of a Synergy frame. How should the integrator complete the task?

  A. Add the network to an interconnect bay within a Logical Enclosure (LE)
  B. Add the networks to an uplink set within a Logical Interconnect Group (LIG)
  C. Add the networks to an Enclosure Group (EG)
  D. Add the network sets to a Logical Interconnect Group (LIG)
  A. Add the network to an interconnect bay within a Logical Enclosure (LE)

• Question 10:

  Using a two-port FLM, what is the minimum number of frames needed to implement a solution that includes redundant Composers and Image Streamers?

  A. 1
  B. 2
  C. 3
  D. 4
  C. 3