HP HPE0-S50 Online Practice Questions and Exam Preparation

HP HPE0-S50 Online Questions & Answers

• Question 1:

  DRAG DROP

  A customer needs a Synergy solution configuration with 40Gb uplinks that will connect to network equipment in a different rack.

  Click and drag the cable type on the left to the corresponding distance between the frame and the network equipment on the right to meet the customer's needs.

  Select and Place:

  

  

• Question 2:

  A customer has purchased 15 Synergy Frames with the following components:

  

  150 HPE SY 480 compute modules

  

  15 HPE Synergy D3940 storage modules with 40 disks each

  

  6 Image Streamers

  

  6 Virtual Connect SE 40Gb F8 modules

  

  24 10Gb Interconnect Link Modules

  How many frames can the configuration have for the Logical Enclosure?

  A. 3 frames
  B. 4 frames
  C. 5 frames
  D. 6 frames
  A. 3 frames

• Question 3:

  Refer to the exhibit.

  

  Based on the Synergy configuration shown, what will be the outcome in the event of an end-of-row (EoR) switch failure?

  A. Smartlink will be triggered
  B. There will be no NIC failover.
  C. Uplink bandwidth will decrease.
  D. Server and downlinks will fail.
  B. There will be no NIC failover.

• Question 4:

  Refer to the exhibit.

  

  How should a Synergy integrator pair interconnect bays to set up redundant fabrics in an HPE Synergy 12000 Frame?

  A. Interconnect bays 1 and 2; bays 3 and 4; bays 5 and 6.
  B. Interconnect bays 1 and 4; bays 2 and 5; bays 3 and 6.
  C. Interconnect bays 1 and 6; bays 2 and 5; bays 3 and 4.
  D. Interconnect bays 1 and 3; bays 2 and 4; bays 5 and 6.
  B. Interconnect bays 1 and 4; bays 2 and 5; bays 3 and 6.

• Question 5:

  A customer has a multi-frame Synergy solution. The customer's Support team recently missed some important alerts in its Composer interface because each pair of Composers resides on a separate management network. What should the customer do to minimize the risk of this reoccurring?

  A. Configure HPE Intelligent Management Center.
  B. Implement HPE Synergy Global Dashboard.
  C. Configure Remote Support.
  D. Implement HPE Systems Insight Manager.
  B. Implement HPE Synergy Global Dashboard.

• Question 6:

  A customer is planning an HPE Synergy solution with 20 frames and needs to minimize the number of management ports that are required to connect the frames into the existing management network. Which procedure should the Synergy integrator use to address the customer's concern?

  A. Connect FLMs from all frames into a management ring. Then connect the management ring to the customer's management network using two uplinks.
  B. Connect FLMs from all frames to two external switches for redundancy. Then connect the two uplinks from the two switches into the customer's management network.
  C. Connect the RJ-45 front ports of each frame to two external switches for redundancy. Then connect the uplink from the two switches into the customer's management network.
  D. Connect the RJ-45 front ports of each frame to an external switch. Then connect the uplink from the external switch into the customer's management network.
  A. Connect FLMs from all frames into a management ring. Then connect the management ring to the customer's management network using two uplinks.

• Question 7:

  When should IP addresses be assigned using an IPv4 address pool in the Composer? (Choose two.)

  A. when configuring management NICs in an operating system
  B. when booting to an iSCSI initiator with Image Streamer
  C. when PXE booting from the deployment server
  D. when configuring Composer appliances
  E. when configuring interconnect modules
  B. when booting to an iSCSI initiator with Image Streamer
  C. when PXE booting from the deployment server

• Question 8:

  A customer's Synergy solution configuration needs redundant paths to the drives used in the HPE Synergy D3940 storage module. Which component must be redundant to meet the customer's requirement?

  A. HPE Synergy 12Gb SAS Connection Module
  B. HPE Synergy D3940 storage module
  C. HPE Smart Storage Battery with 260mm Cable Kit
  D. HPE Compute Module Smart Array P542D SAS Cable
  A. HPE Synergy 12Gb SAS Connection Module

• Question 9:

  A Synergy integrator is creating a network that must be connected from the HPE Synergy Virtual Connect SE 40Gb F8 module to an Ethernet switch carrying 500 VLANs for the hypervisor cluster. Which network should the Synergy integrator select during network creation?

  A. Ethernet Tunneled
  B. Ethernet Channeled
  C. Ethernet Tagged
  D. Ethernet Untagged
  A. Ethernet Tunneled

• Question 10:

  A Synergy integrator needs to add more NICs to a server profile.

  What does the integrator need to be aware of when performing this action?

  A. The host needs to be powered off to activate the change.
  B. The Virtual Connect modules need to be rebooted once the profile is applied.
  C. The server profile template must be changed before modifying the server profile.
  D. The host networks will go offline when the profile is assigned.
  C. The server profile template must be changed before modifying the server profile.