HP HPE0-J68 Online Practice Questions and Exam Preparation

HP HPE0-J68 Online Questions & Answers

• Question 41:

  You want to deploy Recovery Manager Central to a customer environment.

  How can you accomplish this? (Choose two.)

  A. Install RMC on top of the virtual or physical RHEL system using the GUI wizard
  B. Deploy an RMC virtual appliance to Microsoft Hyper-V hypervisor
  C. Deploy RMC on top of the virtual CentOS system using the CLI
  D. Deploy RMC on top of the virtual CentOS system using the GUI wizard
  E. Install RMC on the top of the virtual or physical RHEL system using the CLI
  F. Deploy an RMC virtual appliance to VMware ESXi hypervisor
  B. Deploy an RMC virtual appliance to Microsoft Hyper-V hypervisor
  F. Deploy an RMC virtual appliance to VMware ESXi hypervisor

• Question 42:

  You are designing a new HPE 3PAR StoreServ solution.

  Which HPE tool allows editing the Customer Intent Document and adding specific instructions for packing?

  A. One Config Advanced
  B. SAF Collect
  C. NinjaSTARS
  D. Storage Sizing Tool
  A. One Config Advanced

• Question 43:

  You are planning a single-site Nimble solution with iSCSI connectivity. Two 10GbE SFP+ dual port NICs are included in the configuration. You designed an Intelligent Resilient Framework (IRF) stack with HPE FlexFabric 5900CP switches.

  Which statement is correct when discussing the IRF limits for this configuration?

  A. When connecting an iSCSI storage to an IRF stack, a minimum of four 10GbE ports must be used per switch.
  B. A maximum of two switches can be used in an IRF stack when connecting storage.
  C. In an IRF stack with storage connectivity, the 40GbE ports cannot be used.
  D. The used IRF ports for iSCSI traffic have to be configured as 10GbE converged ports.
  A. When connecting an iSCSI storage to an IRF stack, a minimum of four 10GbE ports must be used per switch.

• Question 44:

  Refer to the exhibit.

  

  You are configuring a new HPE array and verifying properties of a set of volumes.

  Which RAID level is used on the VMwareDatastores-GF volume?

  A. RAID 0
  B. RAID 6
  C. Triple Parity+
  D. RAID 5
  B. RAID 6

  ---

  Explanation/Reference:

• Question 45:

  DRAG DROP

  Match each address with the associated address type.

  Select and Place:

  

  

  ---

  Explanation/Reference:

• Question 46:

  DRAG DROP

  Refer to the exhibit.

  

  You create two snapshots of a thin provisioned base volume in an HPE Primera. One snapshot is read only and the other is read-write. A write occurs at the location shown in in the diagram. Place the actions on the left into the order they are taken on the right.

  Select and Place:

  

  

  ---

  Explanation/Reference:

• Question 47:

  A customer purchased a StoreOnce 3620 earlier in the year and has decided to add a 10GBase- adapter to it, which the customer sourced elsewhere and installed themselves. They complain that the new adapter is not configurable.

  What is the most likely reason for this issue?

  A. The StoreOnce software requires updating
  B. Secure boot must be enabled in the BIOS to securely enable HBAs
  C. The customer failed to install a License to Use (LTU) for it
  D. The StoreOnce needs to connect to InfoSight to validate the adapter authenticity
  A. The StoreOnce software requires updating

• Question 48:

  You need to deploy a Recovery Manager Central appliance and integrate it with a customer's 3PAR system.

  Which information must be collected from the customer in order to proceed with the installer? (Choose two.)

  A. StoreOnce store name
  B. vCenter IP address or hostname
  C. HPE 3PAR used capacity
  D. IP address of the RMC
  E. NFS path
  C. HPE 3PAR used capacity
  D. IP address of the RMC

• Question 49:

  You are designing a new HPE 3PAR StoreServ all-flash array for the customer.. Which ratio should you expect to have the highest efficiency?

  A. Read/write ratio
  B. Reclamation ratio
  C. Compaction Ratio
  D. Thin provisioning ratio
  C. Compaction Ratio

• Question 50:

  DRAG DROP

  Match the MSA architecture components with their descriptions.

  Select and Place:

  

  

  ---

  Explanation/Reference: