HP HP2-Z34 Online Practice Questions and Exam Preparation

HP HP2-Z34 Online Questions & Answers

• Question 11:

  Refer to the exhibit

  

  PE-1 receives an IP packet that is destined to 10 1.10 10 and does not have an MPLS header. What does PE-1 do?

  A. drops the packet
  B. adds an MPLS header without a label and forwards the packet to 10.1.1.1 on VLAN 17
  C. adds an MPLS header with label 1150 and forwards the packet to 10.1.1.1 on VLAN 17
  D. forwards the packet to 10.1.1.1 on VLAN 17 without an MPLS header
  A. drops the packet

• Question 12:

  Which statement is correct about a Fibre Channel (FC) node-port (N-port) in a Storage Area Network (SAN) fabric topology?

  A. It is a port on a SAN switch that connects to an initiator or target
  B. It is a port on a SAN switch that connects to a target but never to an initiator
  C. It is a port on an initiator but never a target, and it connects to an extension port (E-port).
  D. It is a port on an initiator or a target, and it connects to a fabric port (F-port)
  C. It is a port on an initiator but never a target, and it connects to an extension port (E-port).

• Question 13:

  HP Comware Switch 1 connects to servers with Converged Network Adapters (CNAs) that send data and FCoE storage traffic Switch 1 should forward all FCoE traffic to an upstream FCoE switch. Switch 2 which will handle all the FLOGI requests, zoning, and FC traffic forwarding.

  What is the correct FCoE mode setting for Switch 1?

  A. NPV
  B. FCF
  C. disabled
  D. hybrid
  B. FCF

• Question 14:

  Refer to the exhibits Exhibit 1

  

  This data center topology is being set up to use SPBM. VMs in the same subnet should be able to communicate at Layer 2 and be isolated at Layer 2 from other subnets. VS110010 was created for VLAN 10 as shown in Exhibit 2. The administrator is configuring a service instance for the VLAN 10 traffic on Switch 1 interface Ten1/0/1.

  What is the correct encapsulation mode?

  A. s-vid101
  B. ta99ed
  C. default
  D. s-vid10
  D. s-vid10

• Question 15:

  Refer to the exhibit

  

  An administrator is configuring an MPLS VPLS Martini solution on PE-1. The VPLS solution should connect customer A sites 1, 2, and 3 Where should the administrator specify the LDP peers and pseudo wire (PW) label for the PWs?

  A. in service instances on interfaces Ten2/0/1 and Ten2/0/2
  B. in a Virtual Switch Instance (VSI) for customer A
  C. in a service instance on interface G1/0/1
  D. in a global cross-connect group
  A. in service instances on interfaces Ten2/0/1 and Ten2/0/2

• Question 16:

  An HP IRF virtual switch with two members is implementing SPBM. The administrator wants to ensure that the master can fail without causing topology changes or changes in forwarding tables in the SPBM region.

  Which setting helps support this requirement?

  A. tandem replication for multicasts
  B. persistent MAC address for IRF
  C. Bidirectional Forwarding Detection (BFD) Multi-Active Detection (MAD) for the IRF link
  D. non-stop-forwarding for SPBM
  C. Bidirectional Forwarding Detection (BFD) Multi-Active Detection (MAD) for the IRF link

• Question 17:

  Refer to the exhibit

  

  These switches form an SPBM region. What is required for load balancing to occur across the links between these switches?

  A. IS-IS cost for each backbone link must be the same (with IS-IS ECMP enabled).
  B. B-VLANs must be configured to use different ECT algorithms.
  C. Tandem multicast mode must be enabled globally
  D. B-VLANs must be assigned to different MSTP instances.
  C. Tandem multicast mode must be enabled globally

• Question 18:

  A large data center needs to extend its Layer 2 connectivity and isolate tenants who might use the same VLAN IDs Which technology accomplishes this goal?

  A. SPBM
  B. Data Center Bridging (DCB)
  C. Multi-VPN-Instance CE (MCE)
  D. TRILL
  A. SPBM

• Question 19:

  Refer to the exhibit

  

  An administrator is setting up this data center topology to use SPBM VMs in the same subnet should be able to communicate at Layer 2 and be isolated at Layer 2 from other subnets. On which Switch 1 interfaces should the administrator enable SPBM?

  A. interfaces Ten1/0/1-Ten1/0/48 and interfaces Forty1/0749-1/0750
  B. interfaces Forty 1/0749-1/075 only
  C. VLAN interfaces 101 and 103
  D. VLAN interfaces 10, 20, and 30
  C. VLAN interfaces 101 and 103

• Question 20:

  An HP Comware switch port is being connected to a server Converged Network Adaptor (CNA). The CNA and the switch port need to communicate about parameters for various priority flow control (PFC) and bandwidth control mechanisms. How does the administrator enable these communications?

  A. Enable PFC globally and then enable PFC on the switch port
  B. Enable the Fibre Channel (FC) fabric port function on the switch port and then set the port as an F-port.
  C. Enable Ethernet Virtual Bridging (EVB) on the switch port.
  D. Enable LLDP globally and then enable Data Center Bridging eXchange (DCBX) TLVs on the switch port
  D. Enable LLDP globally and then enable Data Center Bridging eXchange (DCBX) TLVs on the switch port