HP HP2-T26 Online Practice Questions and Exam Preparation

HP HP2-T26 Online Questions & Answers

• Question 11:

  When connected via a remote iLO session to a new ProLiant Server Blade, how should the system BIOS settings be configured?

  A. The system ROM should automatically configure the entire system, without the need for intervention.
  B. The ACU should be run to configure the Smart Array manually, before configuring the system.
  C. The RBSU should be run to configure the system.
  D. The RBSU for iLO should be run and an account and password set up.
  C. The RBSU should be run to configure the system.

• Question 12:

  You replaced a defective memory module in a ProLiant Blade server. On Boot up, you noticed errors during POST, but the screen cleared before you could see what happened. Where can you view these errors now that the server has booted up to Windows?

  A. Windows Event Viewer Application log
  B. HP Insight Diagnostic POST tab
  C. Integrated Management log
  D. HP Insight Diagnostics Diagnose tab
  C. Integrated Management log

• Question 13:

  Which Advanced Memory Protection (AMP) features are available on a ProLiant BL460c G6? (Select three.)

  A. Memory Non-Lock-Step mode
  B. online replace and addition memory
  C. advanced error checking and correcting
  D. hot plug RAID memory
  E. online spare memory
  F. mirrored memory
  C. advanced error checking and correcting
  E. online spare memory
  F. mirrored memory

• Question 14:

  Which tool is used to enable Memory Lock-Step mode on a BL460c G6?

  A. Insight Agent CLI
  B. ProLiant SmartStart CD
  C. HP System Management Homepage
  D. ROM-Based Setup Utility
  C. HP System Management Homepage

• Question 15:

  Which port must be used to connect to the Onboard Administrator (OA) using Service IP?

  A. any port of the interconnect in bay 1
  B. USB port on active OA
  C. standby OA network port
  D. enclosure link-up port
  D. enclosure link-up port

• Question 16:

  HP standard warranties support the HP hardware. What are HP Care Packs designed to support?

  A. Software
  B. Network
  C. Storage
  D. Business
  A. Software

• Question 17:

  Which CLI commands can be used to determine if networking has been configured properly in Windows? (Select two.)

  A. netconfig
  B. netstat
  C. ipstat
  D. ipconfig
  E. ifconfig
  B. netstat
  D. ipconfig

• Question 18:

  How can you access the RBSU to verify Advanced Processor settings? (Select two.)

  A. Press F9 during POST.
  B. Press F12 during POST.
  C. Use Windows RBSU Configuration Utility.
  D. Use HP Insight Diagnostics Offline Edition.
  E. Use BIOS USB Console.
  F. Use BIOS Serial Console.
  A. Press F9 during POST.
  F. Use BIOS Serial Console.

• Question 19:

  How can a ProLiant server running Linux be rebooted from a remote location?

  A. clicking on Start and then clicking on Shut Down in the remote iLO console screen
  B. using the virtual power off button of the iLO
  C. using the command shutdown now -h in the remote iLO console screen
  D. using the command init 6 in the remote iLO console screen
  A. clicking on Start and then clicking on Shut Down in the remote iLO console screen

• Question 20:

  In a c7000 enclosure, you notice a fan LED flashes amber for about eight seconds and then returns to green. What does this indicate?

  A. The fan is overheating.
  B. The fan has failed.
  C. The fan speed was changed.
  D. The fan firmware was updated.
  D. The fan firmware was updated.