HP HP2-T23 Online Practice Questions and Exam Preparation

HP HP2-T23 Online Questions & Answers

• Question 11:

  Why is it considered a best practice to use tools such as HP Smart Update Manager (SUM) and Virtual Connect Support Utility (VCSU) to deploy firmware components?

  A. These tools are compatible with all versions of firmware
  B. These tools check dependencies and limitations.
  C. These are the only tools that work with Virtual Connect Enterprise Utility (VCEU).
  D. These tools support cross-platform deployments
  B. These tools check dependencies and limitations.

• Question 12:

  An engineer repaired a memory problem in a ProLiant BL460c Gen8 server blade running Windows 2008 R2. What should the engineer do to verify the repair? (Select two.)

  A. Observe the Insight Display at the front of the server after it boots.
  B. Check the Active Health System.
  C. Observe the server console for POST errors.
  D. Reboot the BL460c Gen8 server and run the offline Insight Diagnostics.
  E. Reseat the memory and inform the customer when the job is done.
  A. Observe the Insight Display at the front of the server after it boots.
  D. Reboot the BL460c Gen8 server and run the offline Insight Diagnostics.

• Question 13:

  Where is the data written when power is lost on an HP Smart Array controller?

  A. Master boot record
  B. Flash backed write cache
  C. Network controller
  D. System memory
  B. Flash backed write cache

• Question 14:

  To boot a USB firmware memory key built by the HP USB key utility, where should an engineer insert the key to upgrade the firmware on the server blade?

  A. Redundant Onboard Administrator USB connector
  B. Onboard Administrator USB port
  C. USB key on the server blade
  D. SUV cable USB connector
  B. Onboard Administrator USB port

• Question 15:

  You ate installing a new HP BladeSystem c7000 enclosure. The customer wants to configure the iLO and interconnect IP addresses so that they are automatically maintained during a hardware swap How should you configure the enclosure?

  A. Use the Insight Display fixed IP feature.
  B. Configure the IP on each device and enable one enclosure IP mode.
  C. Use Insight Control Server Deployment to configure the enclosure.
  D. Use Enclosure-Bay IP Addressing.
  D. Use Enclosure-Bay IP Addressing.

• Question 16:

  Which feature should you enable in RBSU in a ProLiant Gen8 server lo reduce processor power usage and improve overall performance in some applications?

  A. OS Control Mode
  B. Processor Core Disable
  C. Intel Hyper-Threading
  D. HP Dynamic Power Savings Mode
  B. Processor Core Disable

• Question 17:

  A customer placed a service call after installing genuine HP memory from a ProLiant DL380 Gen7 server into a new ProLiant DL380 Gen8 server and receiving a POST message that the memory is not HP Smart Memory. What caused this to happen?

  A. The memory is defective and is not discovered during POST.
  B. The memory is not in the correct processor Bank.
  C. Only Gen8 memory can be detected as Smart Memory.
  D. The memory is not authentic HP memory.
  C. Only Gen8 memory can be detected as Smart Memory.

• Question 18:

  What is a distinguishing feature of flash-backed write cache (FBWC)?

  A. It enables disk drive write cache with error checking and correcting (ECC) flash memory.
  B. It uses a fixed read-ahead caching scheme to increase sequential read performance.
  C. It returns write completion status to the operating system after it writes data to the drives.
  D. It uses a capacitor and flash memory to hold data rather than a battery and a DIMM.
  D. It uses a capacitor and flash memory to hold data rather than a battery and a DIMM.

• Question 19:

  Which button should you press to enter the RBSU during POST?

  A. F8
  B. F9
  C. F11
  D. F12
  B. F9

• Question 20:

  What should a system administrator use to save an enclosure backup?

  A. HP One Button Disaster Recovery (OBDR)
  B. SmartStart Scripting Toolkit
  C. Amirrored drive
  D. Aconfiguration script
  D. Aconfiguration script