HP HP2-T23 Online Practice Questions and Exam Preparation

HP HP2-T23 Online Questions & Answers

• Question 91:

  Which HP tool can you use to deploy firmware and software updates to a ProLiant server blade?

  A. Insight Diagnostics
  B. Software Update Manager
  C. System Management Homepage
  D. Service Pack for ProLiant
  B. Software Update Manager

• Question 92:

  What should be installed on a ProLiant Gen8 server to display operating system information within the iLO 4 GUI?

  A. System Management Home Page
  B. HP Management Agents
  C. Agentless Management Service
  D. ProLiant Support Pack
  C. Agentless Management Service

• Question 93:

  An engineer replaced a tape drive that failed. What is the best method for testing this drive during business hours?

  A. Run online Insight Diagnostics and check the IE logs.
  B. Use L and TT to perform an assessment test.
  C. Use L and T T to perform a device self test.
  D. Run offline insight Diagnostics.
  C. Use L and T T to perform a device self test.

• Question 94:

  An administrator must replace a defective processor located in slot 1 in an Intel-based ProLiant DL5860 Gen8 server: What should the administrator do?

  A. Install the second processor in slot 1.
  B. Confirm that processor memory board 1 is installed before removing the processor.
  C. Open the fan cage before removing the processor.
  D. Open the heat sink retaining bracket to remove the processor.
  D. Open the heat sink retaining bracket to remove the processor.

• Question 95:

  HP standard warranties support HP hardware. What are HP Care Packs designed to support?

  A. Software
  B. Storage
  C. Business
  D. Network
  C. Business

• Question 96:

  A c7000 enclosure is fully populated with power supplies. Each power supply will have 2400W available if the N+1 power mode is configured. What is the total amount of available power in the enclosure?

  A. 7200W
  B. 12000W
  C. 14400W
  D. 16800W
  C. 14400W

• Question 97:

  A support engineer is troubleshooting a ProLiant DL360p Gen8 server.A hard disk m a four drive RAID 5 set has failed.The engineer notices that on three of the drives, the LEO labeled D on the exhibit is on.What does the condition indicate?

  

  A. Hot swapping of the failed drive is not supported in this condition
  B. The LED indicates failure and predictive failure alerts. Two additional drives in the RAID set are at risk of failing and need to be replaced
  C. The drives should not be removed when this LED is illuminated
  D. The drive failure has corrupted three drives in the RAID set. The array must be rebuilt and data restored from backup
  C. The drives should not be removed when this LED is illuminated

• Question 98:

  Which statements are correct about the HP Customer Self Repair (CSR) program?

  A. A travel and labor charge applies when customers request HP to replace parts.
  B. A travel and labor charge does not apply when customers decline to replace a mandatory CSR part.
  C. A travel and labor charge does not apply when customers decline to replace an optional CSR part.
  D. A travel and labor charge applies when customers decline to replace an optional CSR part.
  A. A travel and labor charge applies when customers request HP to replace parts.

• Question 99:

  A customer asks you to check on the remaining life of the solid state disk drives. Where can you access the SMARTSSD Wear Gauge?

  A. Array Configuration Utility (ACU)
  B. Option ROM Configuration for Arrays (ORCA)
  C. iLO home page
  D. Integrated Management log (IML)
  C. iLO home page

• Question 100:

  Which type of memory is used on the HP Smart Array controller cache?

  A. RDRAM
  B. DRAM
  C. SRAM
  D. SDRAM
  B. DRAM