HP HP2-T16 Online Practice Questions and Exam Preparation

HP HP2-T16 Online Questions & Answers

• Question 1:

  Into which range do reserved TCP/IP server ports generally fall?

  A. 0-1023
  B. 1-512
  C. 21-80
  D. 1024-8080
  A. 0-1023

  ---

  {\rtf1\ansi\ansicpg936\deff0\deflang1033\deflangfe2052{\fonttbl{\f0\fnil\fcharset0 MS Shell Dlg 2;}} \viewkind4\uc1\pard\lang2052\f0\fs17 Industry Standard Architecture - Student Guide 2 - Page 53:\par Using ports to define services Server ports, or ports associated with services generally fall within the range of 0-1023.\par }

• Question 2:

  Your customer wants to guard against the simultaneous loss of any two disk drives in his RAID array. Which RAID level can be used to accomplish this?

  A. RAID 1
  B. RAID 3
  C. RAID 5
  D. RAID 6
  D. RAID 6

  ---

  {\rtf1\ansi\ansicpg936\deff0\deflang1033\deflangfe2052{\fonttbl{\f0\fnil\fcharset0 MS Shell Dlg 2;}} \viewkind4\uc1\pard\lang2052\f0\fs17 Industry Standard Architecture - Student Guide 1 - Page 261\par RAID 6 ?Advanced data guarding\par RAID 6, also known as Advanced Data Guarding (ADG), provides high fault tolerance. It distributes two sets of parity data protecting against two drive failures.\par As the graphic shows, parity (P) is written twice for each piece of data (D). These two sets are different, and each set occupies a capacity equivalent to that of one of the constituent drives.\par }

• Question 3:

  In systems with AMD processors, what allows communication between processors and the I/O subsystem?

  A. Northbridge
  B. Southbridge
  C. HyperTransport link
  D. APIC
  E. QuickPath Interconnect
  C. HyperTransport link

  ---

  {\rtf1\ansi\ansicpg936\deff0\deflang1033\deflangfe2052{\fonttbl{\f0\fnil\fcharset0 MS Shell Dlg 2;}} \viewkind4\uc1\pard\lang2052\f0\fs17 Industry Standard Architecture - Student Guide 1 - Page 37\par AMD processors are able to communicate with each other through HyperTransport point-to-point links. This enables one processor to access the memory connected to another processor. Inside the processor, a crossbar switch connects the processor, memory controller, and HyperTransport links.\par AMD processors also use HyperTransport links to connect to the I/O subsystem.\par The links on particular processors are connected to I/O tunnels that support the I/O devices.\par All other processors can communicate with the I/O system through the HyperTransport links.\par Legacy devices are also connected to one of the I/O tunnels.\par }

• Question 4:

  Which statements are true about AMD 2P or 4P system architecture? (Select three)

  A. Requests for memory access are handle by the Northbridge ASIC.
  B. Memory must be installed in banks corresponding to the installed processors.
  C. Each processor has its own memory controller
  D. The maximum amount of memory can be installed, regardless of the number of installed processors.
  E. Requests for memory access are handle directly by the corresponding processor and relayed through the HyperTransport link.
  F. Communications between CPU and memory is handle through the QuickPath Interconnect.
  B. Memory must be installed in banks corresponding to the installed processors.
  C. Each processor has its own memory controller
  E. Requests for memory access are handle directly by the corresponding processor and relayed through the HyperTransport link.

• Question 5:

  You added memory to a 4-socket AMD Operton-based server. The new memory does not show in POST and the operating system does not see it. You verified that the memory is correct for this server model. Why is the memory not being used?

  A. System Maintanance Switch DIP SW2 is set to ON and the Configuration Lock is enabled.
  B. You exceeded the server's maximum memory capacity.
  C. The memory was added to a bank with no process in the adjoining socket.
  D. There is a memory size mismatch on DR2 and AMD HyperTransport bus.
  C. The memory was added to a bank with no process in the adjoining socket.

• Question 6:

  Which port type does a host server use when connected to an FC-SAN?

  A. N_Port
  B. E_Port
  C. G_Port
  D. F_Port
  A. N_Port

  ---

  {\rtf1\ansi\ansicpg936\deff0\deflang1033\deflangfe2052{\fonttbl{\f0\fnil\fcharset0 MS Shell Dlg 2;}} \viewkind4\uc1\pard\lang2052\f0\fs17 Industry Standard Architecture - Student Guide 1 - Page 289:\par The three basic types of ports used within a FC-SAN are:\par N_port---Node port to either a disk or server \par F_port---Fabric port, found only on a switch; connects only to the N_port by PtP connection\par E_port--- Expansion port on a switch used to connect to other switches\par }

• Question 7:

  A customer is using the GFS backup rotation plan with the weekly backups occuring Friday evening. The customer needs to restore a file that was known to be good on Friday morning. From which backup should the customer restore?

  A. Father
  B. Differential
  C. Grandfather
  D. Son
  D. Son

  ---

  {\rtf1\ansi\ansicpg936\deff0\deflang1033\deflangfe2052{\fonttbl{\f0\fnil\fcharset0 MS Shell Dlg 2;}} \viewkind4\uc1\pard\lang2052\f0\fs17 Industry Standard Architecture - Student Guide 2 - Page 302:\par Grandfather-Father-Son tape rotation \par The system administrator typically performs a full backup every Monday (father) and incremental backups on Tuesdays, Wednesdays, and Thursdays (sons). The administrator performs another full backup at the end of the week (father) and another at the end of the month (grandfather).\par }

• Question 8:

  You are integrating a RAID array for mixed read/write applications. What should you do with striping to achieve optimal performance?

  A. Accept the default stripe size.
  B. Disable striping.
  C. Increase the stripe size.
  D. Decrease the strip size.
  A. Accept the default stripe size.

  ---

  {\rtf1\ansi\ansicpg936\deff0\deflang1033\deflangfe2052{\fonttbl{\f0\fnil\fcharset0 MS Shell Dlg 2;}} \viewkind4\uc1\pard\lang2052\f0\fs17 Industry Standard Architecture - Student Guide 1 - Page 265\par Optimizing the stripe size\par Type of server application Suggested stripe size change\par Mixed read/write Accept the default value\par }

• Question 9:

  What is the virtual machine instance commonly called?

  A. guest
  B. host
  C. partition
  D. hypervisor
  A. guest

• Question 10:

  What is the software abstraction layer instance commonly called?

  A. guest
  B. partition
  C. hypervisor
  D. mirror
  C. hypervisor

  ---

  {\rtf1\ansi\ansicpg936\deff0\deflang1033\deflangfe2052{\fonttbl{\f0\fnil\fcharset0 MS Shell Dlg 2;}} \viewkind4\uc1\pard\lang2052\f0\fs17 Industry Standard Architecture - Student Guide 1 - Page 86\par The software abstraction layer is typically referred to as a hypervisor or a virtual machine monitor.\par }