HP HP0-S35 Online Practice Questions and Exam Preparation

HP HP0-S35 Online Questions & Answers

• Question 131:

  A customer requires the onboard network ports on a ProLiant BL460c Gen8 Windows 2008 R2 server to be bonded together for improved performance and redundancy What should be used to configure this?

  A. Onboard Administrator Enclosure Bay IP Addressing
  B. HP Network Configuration Utility
  C. Onboard Administrator VLAN settings
  D. Windows 2008 Server Manager
  B. HP Network Configuration Utility

• Question 132:

  A customer wants to update the SPP on five Windows 2008 R2 and five RHEL6 servers running in an HP Bladesystem C7000 chassis. What is the fastest way to achieve this?

  A. Boot each server from the SPP DVD, using the Onboard Administrator
  B. Run the SPP on each server using the rcmd command on Windows and remote SSH script on RHEL
  C. Update all targets remotely at the same time from one instance of HP Smart Update Manager from a client
  D. Update all Windows servers from one client using HP Smart Update Manager followed by all RHEL servers
  C. Update all targets remotely at the same time from one instance of HP Smart Update Manager from a client

  ---

  http://bizsupport2.austin.hp.com/bc/docs/support/SupportManual/c03520794/c03520794.pdf

  - Deployment of software for single or one-to-many HP ProLiant servers (supported in Windows and Linux environments). HP normally relies on their own homogenized method. Doing all the servers at once would be a typical approach

  

• Question 133:

  Which HP tool allows you to create a report of the complete firmware installed on an HP BladeSystem server?

  A. Server Migration
  B. Capacity Advisor
  C. Smart Update Manager D. ProLiant Support Pack
  C. Smart Update Manager D. ProLiant Support Pack

• Question 134:

  After a power failure, how long will the data be retained on the cache of an FBWC of a Smart Array Controller?

  A. 24 hours
  B. 48 hours
  C. 72 hours
  D. indefinitely
  E. FBWC does not protect cache data with power failure
  D. indefinitely

  ---

  http://h18004.www1.hp.com/products/quickspecs/14228_div/14228_div.PDF

  

• Question 135:

  Using HP Agentless Management, which components offer pre-failure alerting?

  A. power supplies
  B. fans
  C. memory
  D. processors
  C. memory

  ---

  http://h30507.www3.hp.com/t5/Coffee-Coaching-HP-and-Microsoft/HP-ProLiant-Gen8- Agentless-Management-Overview/ba-p/10857

• Question 136:

  A customer adds a BL460c G7 Blade to a c-Class enclosure with Virtual Connect (VC) installed, boot the server, and sets PXE on the second NIC in the ROM Base Setup Utility (RBSU). The blade connects, but due to a network issue, does not complete, and the blade is cold booted. Now the blade never connects to the HP Insight Control Deployment Server. What is needed to enable the blade to always connect to the deployment servers?

  A. Set PXE on the first NIC in the server profile
  B. Enable SmartLink on the VC profile on the second NIC
  C. Set PXE on the second NIC in the VC profile
  D. Recreate the VC profile with PXE enabled on the second NIC
  C. Set PXE on the second NIC in the VC profile

• Question 137:

  During the initial set of an HP ProLiant Gen8 server using Agentless Management, where should you configure the SNMP Alert Destination?

  A. System Management Homepage
  B. RBSU
  C. iLO interface
  D. System Insight Manager
  C. iLO interface

• Question 138:

  What is the definition of a Hot aisle?

  A. Servers facing Front to font
  B. Servers facing back to front
  C. Servers facing back to back
  D. Servers facing front to back
  C. Servers facing back to back

  ---

  http://www.42u.com/cooling/hot-aisle-containment.htm

  

• Question 139:

  When installing a Modular Cooling System (MCS) G2, which safely considerations must be implemented? (Select two)

  A. Install the MCS G2 free of the adjacent racks
  B. Plug the power supply cables for the MCS G2 in grounded sockets
  C. Verify the maximum water pressure in the MCS G2 does not exceed 0.4 bar (6 PSI)
  D. Use aluminum piping for the water supply
  E. Attach the MCS G2 rack to the grounding system
  F. Verify the temperature inside the MCS G2 does not exceed 20 degree Celsius (68 Fahrenheit)
  B. Plug the power supply cables for the MCS G2 in grounded sockets
  E. Attach the MCS G2 rack to the grounding system

  ---

  http://h10032.www1.hp.com/ctg/Manual/c02776624.pdf - Page 20

  NOT A - http://h10032.www1.hp.com/ctg/Manual/c02776624.pdf - Page 8 The HP MCS G2 offers on incremental data center cooling solution that is capable of cooling 35 kW of heat from one IT rack or two IT racks. The two basic ways to deploy the HP MCS G2 are as a standalone unit or to place it in a row adjacent to other HP MCS G2 units or standard equipment racks.

  NOT C - http://h10032.www1.hp.com/ctg/Manual/c01363784.pdf - Page 7 The HP Modular Cooling System G2 is tested to the maximum pressure (PS) of 8 bar (116 PSI) without fluid trapped inside by closed, external valves.

  NOT D - http://h10032.www1.hp.com/ctg/Manual/c02776624.pdf - Page 42 Plumbing materials to avoid The following materials should not be used with a closed water system: Oxidizing biocides Aluminum components High zinc/brass components Non-stainless steel iron components

  NOT F - http://h10032.www1.hp.com/ctg/Manual/c02776624.pdf - Page 38 The charts in figures 27 and 28 offer a guideline for determining the approximate amount of heat that can be removed from HP MCS G2 single and dual rack configurations based on 20

• Question 140:

  What is the minimum number of CPU sockets that must be populated in a BL890c i2?

  A. 1
  B. 2
  C. 4
  D. 6
  C. 4

  ---

  Reference: http://h18004.www1.hp.com/products/quickspecs/13619_na/13619_na.HTML (Step 2:Choose Required Options; hp processors, see the note)

  Upgradeable to eight (8) processors

  NOTE: The HP Integrity BL890c i2 supports 4, 5, 6, 7, or 8 processor configurations. Processors must be identical.