Huawei H35-211 Online Practice Questions and Exam Preparation

Huawei H35-211 Online Questions & Answers

• Question 41:

  (single) The UA5000 supports the SIP protocol. When the SIP AG accesses the IMS network, which device is connected to the IMS?

  A. AGCF
  B. S-CSCF
  C. I-CSCF
  D. P-CSCF
  D. P-CSCF

• Question 42:

  (single) When locating ADSL/ADSL2+ failure, which of the following reasons may cause the user to make a call but not to access the Internet?

  A. Line configuration template interleaving depth configuration is unreasonable
  B. ADSL Modem failure
  C. User external line interruption
  D. None of the above
  B. ADSL Modem failure

• Question 43:

  (multiple) What are the possible reasons why the ONU cannot go online?

  A. The optical power received by the ONT is greater than the overload optical power.
  B. The optical power received by the ONT is less than the sensitivity value.
  C. Authentication information conflict or configuration error
  D. ODN logical distance exceeds the standard range
  A. The optical power received by the ONT is greater than the overload optical power.
  B. The optical power received by the ONT is less than the sensitivity value.
  C. Authentication information conflict or configuration error
  D. ODN logical distance exceeds the standard range

• Question 44:

  (single) Regarding the IP routing, which of the following is correct?

  A. Routing is the concept of the second layer in the OSI model.
  B. Any route must include the following three parts: source address, destination address, and next hop.
  C. In the LAN, routing includes the following two parts: IP address and MAC address.
  D. IP routing is the path information that guides IP packet forwarding.
  D. IP routing is the path information that guides IP packet forwarding.

• Question 45:

  Type B protection provides redundant protection for both OLT PON ports and backbone fibers when OLT or OLT PON If the port or trunk fiber fails, manually switch to another language?

  A. True
  B. False
  B. False

• Question 46:

  (Radio) Regarding multicast, the following description is incorrect

  A. Add Lgmp user under BTV, and by default, multicast users can watch 8 programs.
  B. The user-issued Report is captured in the single board logic and sent to the single board CPU
  C. Device-based global configurations of Layer 2 groups refer to common parameters of protocols ( IGMP Proxy, GMP Snoop) to all
  D. When the igmp match mode disables, you need to configure the multicast program group
  D. When the igmp match mode disables, you need to configure the multicast program group

• Question 47:

  The (radio) 10G GPON system uses XGEN frames to encapsulate data, and the PORT ID is defined in the XGEN header as () bits.

  A. 18
  B. 12
  C. 14
  D. 16
  D. 16

• Question 48:

  Under the H.248 protocol, if the signaling IP and media IP are both 10. 1 1 100/8, voice gateway is 10. 1 1 1. When configuring voIP service, the following command is incorrect

  A. Using the command ip address media10 in voip mode. 1 1 10010 1 1 1 Configure the media IP
  B. Use the reset coldstart command under Voice Interface to make the interface property configuration take effect
  C. Use the if-h248 attributei command to configure interface properties under the voice interface
  D. Using the command ip address signaling10 in voip mode. 1 1 10010 1 1 1 Configure the signaling IP
  D. Using the command ip address signaling10 in voip mode. 1 1 10010 1 1 1 Configure the signaling IP

• Question 49:

  (multiple) What are the factors that may affect VLAN partitioning and planning when designing FTTx services?

  A. Customer type
  B. Number of services and types of business for ordinary users
  C. Number of OLT access users
  D. Available VLAN resources
  A. Customer type
  B. Number of services and types of business for ordinary users
  C. Number of OLT access users
  D. Available VLAN resources

• Question 50:

  (single) In the Solaris environment, which of the following commands (parameters) is used to unconditionally abort the process?

  A. kill -7 pid
  B. kill -8 pid
  C. kill -9 pid
  D. kill -10 pid
  C. kill -9 pid