EMC E20-616 Online Practice Questions and Exam Preparation

EMC E20-616 Online Questions & Answers

• Question 61:

  Which action needs to be taken if the Backend Cabling Verification fails after a Data Center relocation?

  A. Contact PSE Lab for assistance.
  B. Relocate the cables shown as faulted.
  C. Replace the cables shown as faulted.
  D. Power down and re-start the Backend Cabling Verification script.
  A. Contact PSE Lab for assistance.

• Question 62:

  Where are the daisy chained DAEs for engine 3 located in a fully populated VMAX 10K (987) dense configuration?

  A. System Bay 3 only.
  B. System Bay 3 and bottom of Storage Bay 1B.
  C. Bottom of Storage Bay 1B only.
  D. System Bay 3 and top of Storage Bay 1B.
  B. System Bay 3 and bottom of Storage Bay 1B.

• Question 63:

  What is the maximum amount of cache available in a VMAX 20K Engine using only 8GB DIMM?

  A. 128GB
  B. 256GB
  C. 64GB
  D. 32GB
  A. 128GB

• Question 64:

  What is the maximum amount of cache that can be configured in a Symmetrix VMAX 20K?

  A. 128 GB / engine 1 TB / array
  B. 128 GB / engine 512 / array
  C. 256 GB / engine 1 TB / array
  D. 256 GB / engine 2 TB / array
  D. 256 GB / engine 2 TB / array

• Question 65:

  Refer to the Exhibit.

  

  What is the VMAX 10K component illustrated as 'B'?

  A. SIB
  B. Filler
  C. BE I/O
  D. FE I/O
  A. SIB

• Question 66:

  Refer to the Exhibit.

  

  While configuring a Multi-Engine VMAX 20K, the CE is connecting Engine numbers 4 and 5 with cables. What is the type and sequence of connections required to connect the Highest Engine number?

  A. Purple Cable; connects B to C and A to 1
  B. Green Cable; connects B to C and A to 1
  C. Purple Cable; connects B to C and D to 1
  D. Green Cable; connects B to C and D to 1
  A. Purple Cable; connects B to C and A to 1

• Question 67:

  Customer creates 30 DRX devices on a source VMAX and 60 DRX devices on a target VMAX. After that, they execute the SRDF Compare Tool to check any inconsistency; but the report is empty. Why is the report not displaying those extra 30 devices?

  A. The Compare RDF Tool does not show dynamic devices.
  B. A Dynamic Group needs to be created first.
  C. DRX devices were not paired yet.
  D. Enginuity versions are different.
  A. The Compare RDF Tool does not show dynamic devices.

• Question 68:

  What is a SymmWin Best Practice when configuring disk drives?

  A. Smaller drives perform better.
  B. Go deep then wide when adding drives.
  C. Protection type is irrelevant.
  D. Use Raid 5 instead of Raid 6 when data availability is secondary.
  D. Use Raid 5 instead of Raid 6 when data availability is secondary.

• Question 69:

  You are preparing to run a health check on a VMAX 10K and log into the Service Processor, but cannot locate the icon for Simplified SymmWin on the desktop. What is the most likely reason Simplified SymmWin is not available?

  A. The VMAX is running Enginuity version 5875
  B. Simplified SymmWin is not supported on VMAX 10K
  C. Engineering credentials are required for Simplified SymmWin
  D. Service Processor code upgrade has not been committed
  A. The VMAX is running Enginuity version 5875

• Question 70:

  Refer to the Exhibit.

  

  Which cable should be connected to the VMAX Service processor illustrated as '5'?

  A. Ethernet: CS-Spare
  B. Ethernet: Highest Engine number
  C. Ethernet: Customer Network
  D. Ethernet: Lowest Engine number
  A. Ethernet: CS-Spare