EMC E20-575 Online Practice Questions and Exam Preparation

EMC E20-575 Online Questions & Answers

• Question 11:

  Which RecoverPoint CLI command can be used to show a summarization of the errors and warnings for either one site or the entire RecoverPoint system?

  A. get_rpa_states
  B. get_events_log
  C. get_system_status
  D. get_clusters_topology
  B. get_events_log

• Question 12:

  A RecoverPoint administrator needs to add a local copy to three existing Consistency Groups. The RecoverPoint system currently contains 100 Consistency Groups. Each group has one remote copy with 80 replication sets. Each cluster contains eight physical RPAs.

  However, the administrator is unable to add all the local copies. What is a cause for this issue?

  A. Consistency Group copy cannot have 1024 volumes within the copy
  B. Cluster has the maximum number of RPAs and cannot be expanded
  C. Addition of the local volumes will exceed the 16K volume limit per cluster
  D. RecoverPoint system needs to be converted to a RP/EX system to support the extra volumes
  A. Consistency Group copy cannot have 1024 volumes within the copy

• Question 13:

  Which RPA interface is used for management?

  A. eth1
  B. eth0
  C. iSCSI-1
  D. iSCSI-2
  A. eth1

• Question 14:

  Where are incoming writes sent to during the Write phase of the RecoverPoint workflow?

  A. Production Journal
  B. Consistency Groups' assigned RPA
  C. Remote clusters' primary RPA
  D. Copy Journal
  A. Production Journal

• Question 15:

  A RecoverPoint system has been deployed with XtremIO at production and disaster recovery sites. What is an accurate statement, if the replication mode for a Consistency Group has been set as "Continuous"?

  A. Effective RPO will be 0 seconds
  B. Set customized time between cycles
  C. Effective RPO can be
  D. Set minimum time between cycles
  D. Set minimum time between cycles

• Question 16:

  A RecoverPoint administrator is using the CLI to create a new Consistency Group. After beginning the process by running the command create_group, what is the next command that needs to be run?

  A. add-replication_volume
  B. create_replication_volume
  C. create_production_copy
  D. add_group_set
  B. create_replication_volume

• Question 17:

  What is a possible option to store the "Collect System Information" file using RecoverPoint Unispehre?

  A. FTP server configured on the RPA cluster
  B. External temporary FTP server
  C. Local RPA
  D. Syslog server
  A. FTP server configured on the RPA cluster

• Question 18:

  Which attributes can affect the Distribution phase of Consistency Groups?

  A. Copy location, WAN bandwidth, and replication type
  B. Change rate of the applications and number of replication sets
  C. Journal volume performance, storage array performance, and copy volume performance
  D. Compression and deduplication settings of the Consistency Group
  A. Copy location, WAN bandwidth, and replication type

• Question 19:

  Which tools are listed under "System Analysis and Tools" selection of Unisphere for RecoverPoint?

  A. Users and Security, Configure System Reports and Alerts, Collect System Information
  B. Detect Bottlenecks, Balance Load, Configure System Reports and Alerts
  C. Users and Security, Configure System Reports and Alerts, Change Security Level
  D. Detect Bottlenecks, Balance Load, Collect System Information
  D. Detect Bottlenecks, Balance Load, Collect System Information

• Question 20:

  Which parameter is used as the Locking ID for a RecoverPoint/CL license?

  A. RecoverPoint Cluster ID
  B. RecoverPoint System ID
  C. Array serial number if VNX arrays are used
  D. VPLEX Cluster ID if protecting virtual volumes
  A. RecoverPoint Cluster ID