A technician is creating a virtual disk in the DRAC (2x 4 TB NL-SAS in RAID 1) to install Windows 2016. They manually boot to the OS installation media without using the Lifecycle Controller OS Deployment wizard. Only the first 2048 GB on the virtual disk can be partitioned.
How should the technician obtain access to the remaining 2 TB (approximately) of storage?
A. Delete the 4 TB virtual disk and create a virtual (boot) disk no longer than 2048 GB.
B. Upgrade to a newer version of the operating system.
C. Use the lifecycle Controller's OS Deployment Wizard to deploy the OS on this server.
D. Use F2 to go into the BIOS, change the BIOS boot mode to UEFI, and try again.
A server is equipped with 2 CPUs and 12x 8 GB DIMMs, for a total of 96 GB. The OS is not seeing all the memory. Which memory mode should be configured so that all memory is seen by the OS?
A. Mirroring
B. Advanced ECC
C. Optimizer
D. Sparing
A technician needs to set a server to always attempt PXE boot before booting to the hard drive. What actions does the technician need to take to achieve this?
A. Change the Boot Sequence so the network card is first Remove all boot options except network card
B. Change the Boot Sequence so the network card is first Disable the boot option for the hard drive
C. Set the Legacy Boot Protocol for the network card to PXE Change the Boot Sequence so the network card is first
D. Set the Legacy Boot Protocol for the network card to PXE Select PXE Boot from F11 Boot Manager
A user has a fully configured PowerEdge R640 and an iSM installed on their Windows 2016 operating system. They now want to install OMSA to enable them to have alerts sent out in-Band to a management console.
What does the user need to consider?
A. OMSA can be installed on the same operating system with ISM, provided both OMSA and iSM have the same firmware version revisions.
B. iSM must be uninstalled before OMSA is installed.
C. iSM must be installed before OMSA can be installed.
D. OMSA can be installed on the same operating system with iSM without restrictions.
A technician receives a repurposed PowerEdge server. After racking and cabling the server, the technician attempts to log into the iDRAC but cannot do so. The default account has been disabled.
What method can be used to enable the default login account?
A. Run the racadm recreset command from the host OS.
B. Run the racadm recresetcfg command from the host OS.
C. SSH into the iDRAC and run the racadm racresetcfg command.
D. SSH into the iDRAC and run the racadm racreset command.
A technician is installing a new server and is not getting any link lights on the iDRAC management port. They have verified that the cable and switch port are working. What could be causing this issue?
A. iDRAC has an Express license
B. IP has not been set in the Lifecycle Controller
C. iDRAC has been disabled in the Lifecycle Controller
D. iDRAC firmware update is currently in progress
What can a technician do to ensure that no malicious code can be introduced into any of the servers through physical access?
A. Set USB 3.0 to disabled
B. Set Secure Boot Policy to enabled
C. Set User Accessible Ports to disabled
D. Set UEFI Variable Acces to disabled
A technician creates two virtual disks and assigns a dedicated hot spare to each virtual disk. They also create a global hot spare. A drive fails on the second virtual disk.
What is the result?
A. Dedicated hot spare for the virtual disk replaces the failed drive.
B. Global hot spare replaces the failed drive.
C. Copyback operation occurs between the failed drive and the dedicated hot spare.
D. Copyback operation occurs between the failed drive and the global hot spare.
A technician needs to install the OS on a server remotely using iDRAC. What is the minimum iDRAC license required to perform this task?
A. Express
B. Enterprise
C. Basic
D. Baseboard Management Controller
A technician needs to replace a server component with orange tabs/releases. Which set of paired steps should the technician take to complete this task?
A. Power off the server Apply anti-static procedures
B. Remove power cables Cold swap the component
C. Cold swap the component Apply anti-static procedures
D. Hot swap the component Apply anti-static procedures
Nowadays, the certification exams become more and more important and required by more and more enterprises when applying for a job. But how to prepare for the exam effectively? How to prepare for the exam in a short time with less efforts? How to get a ideal result and how to find the most reliable resources? Here on Vcedump.com, you will find all the answers. Vcedump.com provide not only EMC exam questions, answers and explanations but also complete assistance on your exam preparation and certification application. If you are confused on your DES-4121 exam preparations and EMC certification application, do not hesitate to visit our Vcedump.com to find your solutions here.