A technician is working on an operational PowerEdge R640 server that cannot be rebooted. Observing that all drives are hot-swappable devices, the technician decides to remove a drive that has been giving intermittent errors. After the single drive is removed the operating system crashes.
What could have caused the operating system to crash?
A. System Lockdown mode was enabled, which does not allow any component to be hot-swapped
B. iDRAC was not configured for hot-swappable components
C. Drive was part of a RAID 0 virtual disk
D. PERC was configured to allow a single drive removal
A technician wants to move memory from a few older systems into a newer system. What is the most efficient method to accomplish this task?
A. Power down all of the older servers to physically check the memory Move any matching memory to the new server
B. Use iDRAC to view the memory details of the older systems Power down the servers to move matching memory to the new server
C. Back up the server profile on the older server Move the matching memory and import the server profile to the new server
D. Power down any of the older servers to move any memory to the new server Update BIOS to allow mismatched memory
A technician deletes the iDRAC Express license on a R440 server. Which license type is then enabled?
A. iDRAC Express license cannot be deleted
B. iDRAC Basic license
C. iDRAC Enterprise license
D. iDRAC will not have a license until a new one is installed
A technician needs to repurpose a server. What should they do to prepare the server for its new role?
A. Boot into F10, select System Erase, and press "Y" to confirm erase
B. Enable Delete All Settings in the iDRAC Troubleshooting section
C. Boot into F10, navigate to Retire or Repurpose Server, and Select Components to be cleared
D. Boot to Ctrl+S and perform Network Erase
A technician is setting up a previously used server. Upon power up, the PERC alerts them to the presence of a foreign configuration. In the iDRAC storage section, the technician checks Foreign View. The foreign array configuration is the same as the configuration needed for the new project.
What is a recommended way to prepare the disks for the new project?
A. Edit the foreign configuration and set it to Ready
B. Import the foreign configuration and perform a full initialization
C. Format the foreign configuration and clear the controller configuration
D. Access the Ctrl+R utility, clear the foreign configuration and set up array as needed
A technician is experiencing a compatibility issue that causes network disconnects between the iDRAC firmware and an application that is running. The iDRAC must be rolled back to the last working version. The Enterprise licensed server cannot be rebooted outside scheduled maintenance windows. The next scheduled window is one month away.
Where should the technician perform the Firmware Rollback?
A. Dell System Update Utility
B. iDRAC GUI
C. Repository Manager
D. Lifecycle Controller
A technician needs to add a device to SupportAssist Enterprise. Policy requires that no additional software be installed on the server OS.
In addition to Username and Password, what information is required to add the device?
A. IP address or hostname for the server OS
B. IP address for Dell TechDirect
C. IP address fir OpenManage Server Administrator
D. IP address or hostname for the iDRAC
Eight new servers have arrived at a datacenter. All use static IP addresses for iDRAC. The technician needs to enable these servers to contact the DHCP server on the network to obtain new IP addresses.
What method can the technician use to quickly switch to DHCP?
A. Reboot each server to enable DHCP default settings
B. Boot into CTRL+S and change iDRAC settings to DHCP
C. Use the LCD panel to input a new IP address
D. Log in to the iDRAC and enable DHCP
A technician plugs in a server that has dual power supply units. After powering on the system, they notice that the power supply status indicators blink green then turn off.
What troubleshooting steps should the technician take to resolve this issue?
A. Set the power supply redundancy option to `No Redundancy'
B. Check that the PSUs are not connected to a 240VAC source
C. Update the iDRAC firmware to enable control of new PSU features
D. Check that the PSUs are the same efficiency, feature set, health status, and supported voltage
Before deploying a server, a customer needs a technician to configure the front panel LCD to display a custom message that contains the customer's help desk phone number. However, the server cannot be rebooted.
Where can the technician configure the LCD?
A. Lifecycle Controller
B. iDRAC web GUI
C. System BIOS
D. iSM
Nowadays, the certification exams become more and more important and required by more and more enterprises when applying for a job. But how to prepare for the exam effectively? How to prepare for the exam in a short time with less efforts? How to get a ideal result and how to find the most reliable resources? Here on Vcedump.com, you will find all the answers. Vcedump.com provide not only EMC exam questions, answers and explanations but also complete assistance on your exam preparation and certification application. If you are confused on your DES-4121 exam preparations and EMC certification application, do not hesitate to visit our Vcedump.com to find your solutions here.