A technician needs to remotely update the iDRAC with Lifecycle Controller firmware. They have downloaded the latest iDRAC firmware to the management station and connected to the iDRAC GUI.
What step is required to complete the update?
A. After firmware update completes, restart server
B. Boot the server into F10 to start the firmware update
C. Go to Summary Page and reset the iDRAC
D. Do to the Firmware Update page and upload the iDRAC firmware
A technician needs to configure a server to PXE boot a server setup image with the BIOS in UEFI mode. What action is required to enable this function?
A. Navigate to Network Settings, PXE Device1 Settings, and configure IP
B. Boot to Ctrl+S and configure the NIC for PXE Device1
C. From the iDRAC web interface, select Network Settings, and enable PXE Device1 D. Navigate to Boot Options Settings and set PXE Device1 as first option
What operation should a technician perform to ensure configuration recovery if a server must be physically replaced?
A. Create and export a Server Configuration Profile
B. Back up the Server Profile to a network share or vFlash SD card
C. Enable the export configuration option in System Setup
D. View and export the current hardware inventory
A technician is completing initial firmware updates on a server. One of the updates is a power supply update. During the update process, the server powers off. When the technician hits the power button, they do not see any response from the server.
What is the cause of this issue?
A. Server lost power
B. Control panel or power button failed
C. Front power button is not operational during an update; the technician should use the rear power button.
D. PSU firmware may now be corrupted
A technician is configuring a PowerEdge R640 that has two PSUs. The rack in which it is being installed has two power distribution units (PDUs). No high power such as GPUs are required. The user wants as must redundancy protection as possible.
What is the best way to configure the PSUs?
A. Redundancy Mode set to 2+0 with each PSU power cord connected to a different PDU
B. Redundancy Mode set to1+1 with both PSU power cords connected to the same PDU
C. Redundancy Mode set to 1+1 with each PSU power cords connected to a different PDU
D. Redundancy Mode set to 1+0 with the second PSU stored nearby for quick replacement if the first PSU fails
A technician resets the iDRAC but when they attempt to log back in to the iDRAC is offline. Why is the iDRAC offline?
A. Technician must move the iDRAC network cable back to the iDRAC dedicated NIC
B. DRAC has reset to the default IP address of 192.168.0.120
C. iDRAC is still in the reset process
D. Technician must use iDRAC Direct to enable the iDRAC network
A technician is troubleshooting a server with the following components:
Two CPUs Memory installed in sockets A1, A2, A3, A4, A5, A6, B1, B2, B3, B4, B5 and B6 Expansion cards installed in all expansion slots 6x 1 TB drives configured as a RAID 6 virtual disk The server has the following symptoms: CPU2 has failed Memory in slots B1, B2, B3, B4, B5 and B6 is not accessible Some of the expansion cards have gone offline.
What should the technician do to resolve this issue?
A. Replace the failing CPU, failing memory, and expansion cards
B. Replace the system board
C. Replace CPU2
D. Reboot the server, access the Lifecycle and re-enable CPU2
A technician needs to repurpose a server. The server has dual processors with 18 cores each. The OS only sees 24 threads in total.
Which setting should the technician change in Processor Settings in the System BIOS?
A. Number of Cores per Processor
B. System profile
C. Virtualization Technology
D. Hyperthreading
A server has six memory modules attached to each CPU Memory Optimizer mode is configured. The user now wants to have maximum protection for the memory but cannot afford to lose any memory space. What should the technician install/configure?
A. Six additional memory modules matching the original Switch on Single Rank Spare Mode
B. Six additional memory modules matching the original Switch to Memory Mirroring
C. No additional memory Switch on Single Rank Spare Mode
D. No additional memory Switch to memory Mirroring
A technician is using the iDRAC web GUI to upload a firmware that requires a reboot. They select the update and choose `Apply Update and Reboot Now'. How could the technician determine the status of the firmware update?
A. Access the System Setup Utility > iDRAC Settings and check the completion status in the Job Queue.
B. Log in to the iDRAC web GUI and check the completion status in the Job Queue.
C. Monitor the iDRAC web interface for an "Updates Completed" message in the iDRAC.
D. Access the Lifecycle Controller > Firmware Updates menu and check the completion status in the Job Queue.
Nowadays, the certification exams become more and more important and required by more and more enterprises when applying for a job. But how to prepare for the exam effectively? How to prepare for the exam in a short time with less efforts? How to get a ideal result and how to find the most reliable resources? Here on Vcedump.com, you will find all the answers. Vcedump.com provide not only EMC exam questions, answers and explanations but also complete assistance on your exam preparation and certification application. If you are confused on your DES-4121 exam preparations and EMC certification application, do not hesitate to visit our Vcedump.com to find your solutions here.