Dell Dell Certifications DES-1241 Questions & Answers

• Question 81:

  Which port is used to SSH from one Dell EMC PowerStore appliance to another?

  A. 22

  B. 26

  C. 443

  D. 21

  Correct Answer: A

  Reference: https://topics-cdn.dell.com/pdf/pwrstr-scg_en-us.pdf

• Question 82:

  During Dell EMC PowerStore startup, both appliance nodes have rebooted in service mode. What must be done first to avoid management software conflicts?

  A. Reboot node B

  B. Clear the boot mode

  C. Disable node B boot mode

  D. Return node A to normal mode

  Correct Answer: D

  Reference: https://www.dell.com/support/manuals/pk/en/pkbsd1/powerstore-1000/pwrstr-isg/power-control-procedure-considerations?guid=guid-4352c94e-0ae7-4a2e-8593-9ae135bb9e34andlang=en-us

• Question 83:

  Refer to the exhibit.

  

  What is the result of the network configuration shown for a Dell EMC PowerStore T?

  A. Interfaces are configured for remote replication traffic

  B. Interfaces are configured for PowerStore discovery traffic

  C. Ports 1/1/55 and 1/1/56 are added to a new LACP domain

  D. Ports 1/1/55 and 1/1/56 are added to the VLTi domain

  Correct Answer: B

• Question 84:

  How is a defective DIMM displayed in Dell EMC PowerStore Manager?

  A. Orange with an empty state

  B. Blue with a faulted state

  C. Orange with a faulted state

  D. Blue with an empty state

  Correct Answer: C

• Question 85:

  Refer to the exhibit.

  

  A Storage Administrator noticed a solid amber LED. What does this mean?

  A. Drive identification on

  B. Drive rebuilding

  C. Power up

  D. Drive faulted

  Correct Answer: D

  Reference: https://www.dell.com/support/article/en-pk/sln321266/powerstore-understanding-led-colors-and-states-for-troubleshooting?lang=en

• Question 86:

  What is the last step when adding a drive to a Dell EMC PowerStore system?

  A. Verify the new drive is seen

  B. Add the drive to the pool

  C. Backup the keystore

  D. Zero the drive

  Correct Answer: A

  Reference: https://www.dell.com/support/manuals/pk/en/pkbsd1/powerstore-9000t/pwrstr-isg/install-a-25-drive?guid=guid-bddae51e-a561-4e84-bc0a-c2e99a43f033andlang=en-us

• Question 87:

  

  Refer to the exhibit.

  A Storage Administrator is troubleshooting a Dell EMC PowerStore T hardware issue. They observe that the base enclosure LED circled is blue. What does this indicate?

  A. Base enclosure hardware is operating normally

  B. Base enclosure has a component hardware fault

  C. Cluster has only a single appliance

  D. Appliance has a node in service mode

  Correct Answer: A

  Reference: https://www.dell.com/support/manuals/pk/en/pkbsd1/powerstore-9000t/pwrstr-isg/embedded-module-leds?guid=guid-bc07892c-75cf-43b6-8f17-8a4c49001aebandlang=en-us

• Question 88:

  A Storage Administrator needs to connect through SSH to run svc commands. How is the SSH session configured?

  A. Appliance IP address using port 22

  B. NAS server IP address using port 26

  C. NAS server IP address using port 22

  D. Appliance IP address using port 26

  Correct Answer: C

• Question 89:

  What describes Dell EMC PowerStore X front-end cabling?

  A. Uses internal VMware virtual switching and does not require a management network

  B. Storage and management use the same LACP bonded cable connection

  C. Uses VLTi data switch interconnectivity to support vMotion networks

  D. Management and discovery use the same cables and connections as storage

  Correct Answer: C

• Question 90:

  Through which network do external hosts connect to the cluster for data access?

  A. Management

  B. ICM

  C. ICD

  D. Storage

  Correct Answer: D

  Reference: https://topics-cdn.dell.com/pdf/pwrstr-hcg_en-us.pdf