EMC EMC Other Certification DEA-5TT1 Questions & Answers

• Question 31:

  A VLAN has been configured to have an IPv6 address and a stateless address autoconfiguration for clients. Which IPv6 address prefix will the default gateway have on a client?

  A. fd01::/64

  B. fe08::/64

  C. fe80::/64

  D. ff02::/8

  Correct Answer: C

• Question 32:

  Which port type should be used for only VLAN-unaware devices?

  A. Access port

  B. General port

  C. Hybrid port

  D. Trunk port

  Correct Answer: C

• Question 33:

  Which component translates data, signaling, and protocols to facilitate the data flow between the end device and the network?

  A. Switch

  B. Transceiver

  C. NIC

  D. Port

  Correct Answer: B

• Question 34:

  When configuring a switch, which CLI mode only supports limited show commands?

  A. EXEC

  B. Maintenance

  C. Configuration

  D. EXEC Privilege

  Correct Answer: A

  Reference: https://www.dell.com/support/manuals/us/en/04/poweredge-fx2/dell%20fn%20ioa% 20config_9.8.0.0_pub-v1/cli-modes?guid=guid-aeb7d44d-2413-4da8-b8b9-2f8a26bad435andlang=en-us

• Question 35:

  A network administrator is troubleshooting an OSPF routing issue. There are two paths to a destination network from one switch. In addition, one path is comprised of four 1 Gb links. The other path is comprised of two 1 Gb and two 100 Mb links. The administrator ran several trace routes and notices that the packets are swapping back and forth between the two paths.

  Which corrective action must be taken on the switch infrastructure to correct this issue?

  A. Manually specify the OSPF Router ID on each switch within the path.

  B. Break the paths into multiple OSPF areas.

  C. Change the reference speed used by OSPF in cost calculations on all switches within the path.

  D. Switch all routing protocols to RIPv2.

  Correct Answer: C

• Question 36:

  How many total addresses for network, broadcast, and host are provided with the subnet mask 255.255.255.240?

  A. 8

  B. 16

  C. 24

  D. 48

  Correct Answer: B

• Question 37:

  Which IPv6 scope is used for private addressing on a local network?

  A. Global

  B. Area wide

  C. Unique local

  D. APIPA

  Correct Answer: C

• Question 38:

  What are the Protocol Data Units (PDUs) called at the Transport layer?

  A. Data Payload

  B. Frame

  C. Segment

  D. Packets

  Correct Answer: C

• Question 39:

  Refer to the exhibit.

  

  Switch A and Switch B are connected to each other. Both switches use interfaces Gi1/0/1 and Gi1/0/2. Switch A has a Spanning Tree priority of 8192 and Switch B has the default priority. Which interface becomes the root port?

  A. Switch A Gi1/0/1

  B. Switch A Gi1/0/2

  C. Switch B Gi1/0/1

  D. Switch B Gi1/0/2

  Correct Answer: A

• Question 40:

  You recently joined a company as a junior-level network administrator. You have been tasked with designing the IPv4 scheme for five networks that will be used for training classrooms. These networks need to support no more than 28 devices each. Due to the existing network design, the senior-level network administrator has asked you to work on network 192.168.40.0/24.

  If all networks must be made to logically start with the lowest numbered network and end with the largest numbered network, what is the network ID for the third network?

  A. 192.168.40.32/27

  B. 192.168.40.64/27

  C. 192.168.40.96/27

  D. 192.168.40.128/27

  Correct Answer: B