CWNP CWDP-305 Online Practice Questions and Exam Preparation

CWNP CWDP-305 Online Questions & Answers

• Question 151:

  What happens when you double the channel width (for example, use channel bonding) in a BSS?

  A. Higher noise and lower SNR al the receiver
  B. Lower noise and higher SNR at the receiver
  C. Lower noise and lower SNR at the receiver
  D. Higher noise and higher SNR at the receiver
  A. Higher noise and lower SNR al the receiver

• Question 152:

  You are configuring an 802.11ac AP using manual channel planning. The design specification calls for the current AP to be placed on channel 56 in 5 GHz and to disable the 2.4 GHz radio.

  For what could the 2.4 GHz radio be used if not standard AP operations?

  Response:

  A. PCI DSS encoding
  B. Security monitoring
  C. Bluetooth access
  D. Controller-based channel assignment
  C. Bluetooth access

• Question 153:

  When performing an active site survey in an existing WLAN infrastructure, in addition to gathering throughput data, what other important function are you typically testing simultaneously?

  A. Application filtering
  B. Internet bandwidth
  C. Roaming
  D. ACL configuration
  C. Roaming

• Question 154:

  A designer has created a WLAN design that has been implemented in an organization. The network exists in a four-story building Because each floor has an Identical floor plan, the designer designed only one floor and had the installers duplicate the design on each floor. Now. in validation, it is not performing well What best explains the problem caused by this process?

  A. The result was that APs were above and below each other on the same channel, resulting in excessive CCI The APs should have been deployed so that they were not directly above and below each other and so that they used varying channels between floors
  B. The result was that clients could only connect to APs on their floor and, in a multi-floor deployment, you want clients to connect to APs on other floors in case they roam between floors.
  C. The result was that AC) was increased because the APs were deployed above and below each other on the same channels.
  D. The result was that the frequency utilization was too low for the clients to capture RF waves on which to transmit their signals.
  A. The result was that APs were above and below each other on the same channel, resulting in excessive CCI The APs should have been deployed so that they were not directly above and below each other and so that they used varying channels between floors

• Question 155:

  Which vertically polarized antenna is best suited for a WLAN infrastructure with access points mounted on a ceiling over 6 meters high, where all client stations operate from the floor level?

  A. Patch
  B. Dish
  C. Grid
  D. Low-gain dipole
  D. Low-gain dipole

• Question 156:

  What is the most cost-effective way to accurately measure the height of a ceiling when the use of a ladder is not permitted?

  A. Estimate the height based on known object sizes
  B. Gather measurements from other objects and do the math
  C. Rent a lift-cart to lift you up to the ceiling
  D. Use a laser measure to measure the distance from the floor to the ceiling
  D. Use a laser measure to measure the distance from the floor to the ceiling

• Question 157:

  In a convention center, you have received complaints about the WLAN infrastructure. At this moment, the are only two APs in one auditorium.

  After analyzing the situation, you determined that there are more client devices that the infrastructure was designed for. There are only two APs to support more than 300 devices using the Wi-Fi at the same time.

  What should you do to make the Wi-Fi work as expected?

  Response:

  A. Redesign the entire WLAN
  B. Upgrade the Ethernet connections to MultiGig
  C. Quickly add more APs
  D. Turn up the output power on the APs so that they can handle more clients
  A. Redesign the entire WLAN

• Question 158:

  In addition to a copy of your design, which tools should you use to ensure the installation team deploys APs where you have them designed to be located?

  A. GPS and a map
  B. RF spectrum analyzer and packet capturing software
  C. Ladder and a pen
  D. Camera and marking tools
  D. Camera and marking tools

• Question 159:

  What statements are true regarding jitter and latency?(Choose all that apply.) Response:

  A. Jitter is a measurement of latency variability from one frame to another.
  B. Jitter is a measurement of the variance of the number of frames received from an application for a specific time interval.
  C. Jitter is a measurement of average latency based on a sample of >100 frames.
  D. Latency is a measurement of the time delay experienced in the delivery of a frame.
  E. Latency is a measurement of the time required to transmit two subsequent frames.
  A. Jitter is a measurement of latency variability from one frame to another.
  D. Latency is a measurement of the time delay experienced in the delivery of a frame.

• Question 160:

  After designing a WLAN infrastructure using predictive design software. What's the best way to validate the predictive design in the physical space before deployment, if time and budget allow for it?

  A. Deploy all of the APs as they're shown in the predictive design and perform an active site survey.
  B. Deploy all of the APs as they're shown in the predictive design and perform a passive site survey.
  C. Use a client device positioned where the APs will be installed and measure the signal from the client device.
  D. Perform an AP-on-a-Stick survey using AP locations based upon the predictive design to confirm each AP's placement.
  D. Perform an AP-on-a-Stick survey using AP locations based upon the predictive design to confirm each AP's placement.