CWNP CWDP-304 Online Practice Questions and Exam Preparation

CWNP CWDP-304 Online Questions & Answers

• Question 171:

  What is the most cost-effective way to accurately measure the height of a ceiling when ladder use is not allowed?

  A. Estimate the height based on known object sizes
  B. Gather measurements from other objects and do the math
  C. Rent a lift-cart to lift you up to the ceiling
  D. Use a laser measure to measure the distance from the floor to the ceiling
  D. Use a laser measure to measure the distance from the floor to the ceiling

• Question 172:

  What are the deliverables to your customer after successfully implementing a WLAN infrastructure?

  A. Digital or physical assets, guides, floorplans and configuration documents
  B. Project Charter
  C. Facility blueprints
  D. Nothing is required. The implemented WLAN was deliverable
  A. Digital or physical assets, guides, floorplans and configuration documents

• Question 173:

  In a large enterprise (5000+ wireless users), by what would NOT be a recommended method by which IP addresses and VLANs are assigned to different clients associated to the same AP?

  A. Each SSID is mapped to a static VLAN assignment
  B. Upstream AAA servers dynamically assign VLANs to each user or group profile
  C. Radio signal metrics (RSSI, SNR, etc.) of WLAN clients are triangulated for location-based VLAN assignment during association
  D. Multiple VLAN pools are designated for an SSID and user IP addresses are selected in a round-robin fashion from the associated pools
  C. Radio signal metrics (RSSI, SNR, etc.) of WLAN clients are triangulated for location-based VLAN assignment during association

• Question 174:

  Before performing a pre-deployment passive RF survey of a new deployment using survey mapping software, which of the following must be performed?

  A. Determining AP transmit power
  B. Scaling the map
  C. Selecting antennas
  D. Checking client DTPC settings
  B. Scaling the map

• Question 175:

  Your customer's 802.11n laptops are not able to see the SSID in the 5 GHz band in the conference room.

  When doing a walkthrough using one of these laptops, you confirm that it is unable to see the SSID in the 5 GHz band in the conference room. When using your own 802.11 ac laptop, you're able to see the SSID. What is the most likely cause of this problem?

  A. The AP is configured to use channel 36
  B. The customer laptop does not support Transmit Beamforming
  C. The AP is on channel 144
  D. Their laptops are SISO clients
  C. The AP is on channel 144

• Question 176:

  A business traveler from North America is in Europe. The hotel only provides coverage in 2.4 GHz. The traveler connects to the hotel's SSID and notices an AP in the hotel room.

  However, the laptop reports a very low RSSI when connected. The traveler does not have the same problem when connecting in the lobby.

  What would be the most likely cause of the low RSSI in the hotel room?

  Response:

  A. The AP in the room is transmitting on channel 13 and the traveler associated to a non-channel 13 AP located elsewhere.
  B. The AP in the room is using Bluetooth instead of Wi-Fi.
  C. The AP in the room is using ZigBee instead of Wi-Fi.
  D. The switchport that the AP is connected to is only capable of transmitting at 10 Mbps.
  A. The AP in the room is transmitting on channel 13 and the traveler associated to a non-channel 13 AP located elsewhere.

• Question 177:

  A wireless network with fewer APs at higher power levels to cover a large area is said to be which of the following? Response:

  A. Capacity based
  B. Coverage based
  C. Destined for failure
  D. Ideal for roaming
  B. Coverage based

• Question 178:

  What might limit the ability to locate 802.11 clients using a WLAN infrastructure without an 802.11 tag?

  A. Lack of 802.11k support
  B. When its radio is disabled
  C. When its radio is disabled
  D. When it is off
  D. When it is off

• Question 179:

  When surveying an existing WLAN infrastructure for a possible redesign, you use two Wi-Fi USB adapters to collect RSSI data and two USB spectrum analysis adapters to collect RF spectrum data. Since your laptop doesn't have enough USB ports, you use a 4-port powered USB 3.0 hub.

  What issues could be caused by the use of USB 3.0 that will impact your site survey?

  A. It does not give you enough bandwidth to collect data coming from all of the adapters.
  B. It does not give you enough power for all four of your adapters.
  C. It generates noise in the 2.4 GHz band, giving you a false perception of the noise floor.
  D. It generates noise in the 5 GHz band, giving you a false perception of the noise floor.
  C. It generates noise in the 2.4 GHz band, giving you a false perception of the noise floor.

• Question 180:

  Given A project parameter defines a requirement or constraint (or a project that can be defined before any file imports or design actions. What is an example of a project parameter commonly available in WLAN design software?

  A. AP locations
  B. Minimum required signal strength
  C. AP type selection
  D. Floor plan
  B. Minimum required signal strength