AVIXA AVIXA-CTS Online Practice Questions and Exam Preparation

AVIXA AVIXA-CTS Online Questions & Answers

• Question 261:

  In a request for proposal (RFP) document, what would be the BEST place to find the overall expectations and contractual requirements for the project?

  A. scope of work
  B. block diagram
  C. bill of materials
  D. system drawings
  A. scope of work

  ---

  Explanation

  The Scope of Work (SOW) section in an RFP document outlines the overall expectations and contractual requirements for the project. It provides a detailed description of the work to be performed, including deliverables, timelines, and specific tasks. The SOW ensures that all parties have a clear understanding of the project's objectives and responsibilities, serving as the foundation for the project's execution and management.

• Question 262:

  Assuming a 10' (3 m) ceiling, what is the approximate volume of this room?

  

  A. 300 cubic ft (8.5 m3)
  B. 600 cubic ft (17 m3)
  C. 1500 cubic ft (42.5 m3) o
  D. 6000 cubic ft (162 m3)
  D. 6000 cubic ft (162 m3)

  ---

  Explanation

  To find the volume of the room, we need to calculate the area of the floor and multiply it by the height of the ceiling. The room has a ceiling-mounted DLP projector and a 10' x 58" ceiling-mounted electric screen. Using standard room dimensions, we estimate the room's length and width to fit the equipment layout proportionally.

  Assuming the room dimensions as approximately 20 feet in length and 30 feet in width: Volume=LengthxWidthxHeight\text{Volume} = \text{Length} \times \text{Width} \times \text{Height} Volume=LengthxWidthxHeight Volume=20 ftx30 ftx10 ft=6000 cubic ft\text{Volume} = 20 \text{ ft} \times 30 \text{ ft} \times 10 \text{ ft} = 6000

  \text{ cubic ft}Volume=20 ftx30 ftx10 ft=6000 cubic ft This calculation aligns with the provided options.

  References:

  Axis Communications - Room Design and Calculation Guidelines Standard Architectural Practices

• Question 263:

  A new construction is underway and the walls are framed but not yet drywalled.

  What is the MOST ideal to check at this time?

  A. Projector alignment
  B. Low voltage cabling pathways
  C. Proper sound system equalization
  D. Color matching for ceiling speakers
  B. Low voltage cabling pathways

  ---

  Explanation

  This is the ideal stage for confirming and adjusting cable pathways, as conduit, wall boxes, and cable access are exposed. Once drywall goes up, rework becomes costly and labor-intensive. "Pre-drywall inspection is the critical time to verify cable paths, conduit runs, and accessibility for future service."

  -CTS Exam Guide, Installation Coordination and Site Readiness

• Question 264:

  At what time of day is it BEST to conduct a site survey?

  A. Early mornings
  B. During normal operations
  C. After normal business hours
  D. Only at specially scheduled appointments
  B. During normal operations

  ---

  Explanation

  To understand how a space is truly used, surveys should be done during normal operations. This reveals patterns like ambient noise, occupancy, workflow, lighting, and use of AV systems-all essential for effective design.

  "Observing the space under normal conditions reveals user behavior, usage patterns, and environmental factors."

  -CTS Exam Guide, Needs Analysis and Site Assessment

• Question 265:

  An AV system has a dedicated managed switch with an IP address scheme of 192.168.10.0/24, but one component is not talking to the rest of the system.

  What network property should be checked to ensure it connects to the rest of the system?

  A. QoS
  B. VLAN
  C. Subnet
  D. Gateway
  C. Subnet

  ---

  Explanation

  All devices must share the same subnet to communicate. If a device is on a different subnet (e.g., 192.168.20. x instead of 192.168.10.x), it won't communicate with others unless routing is configured. "Mismatch in subnet masks or incorrect subnet addresses is a common cause of connectivity issues in AV networks."

  -CTS Exam Guide, Networking and IP Configuration Essentials

• Question 266:

  How frequently should a personal fall arrest harness be inspected?

  A. weekly
  B. before each use
  C. at the beginning of each project
  D. at the beginning of each work day
  B. before each use

  ---

  Explanation

  A personal fall arrest harness should be inspected before each use. This is a critical safety measure to ensure that the harness is in good condition and will provide the necessary protection in case of a fall. Regular inspections can identify any wear, damage, or other issues that could compromise the safety of the user.

  References:

  Axis Communications - Safety and Compliance Standards Occupational Safety and Health Administration (OSHA) Guidelines

• Question 267:

  Which of the following translates the IP address of a computer in a local network to a single IP address?

  A. HTTP
  B. MAC
  C. NAT
  D. TCP
  C. NAT

  ---

  Explanation

  Network Address Translation (NAT) is a method used to translate the private IP addresses of computers within a local network to a single public IP address. This allows multiple devices on a local network to access external networks (such as the internet) using a single IP address, conserving the number of public IP addresses needed and providing a layer of security by masking internal IP addresses from the outside world.

• Question 268:

  In an audiovisual system where a touch panel is to be connected to the control system via the LAN, the designer may choose to use a

  A. MAC address.
  B. host IP address.
  C. static IP address.
  D. shared IP address.
  C. static IP address.

  ---

  Explanation

  In an audiovisual system where a touch panel is to be connected to the control system via the LAN, the designer typically chooses to use a static IP address. A static IP address ensures that the touch panel always has the same IP address, making it easier to locate and communicate with within the network. This is crucial in a control system where consistent and reliable communication is necessary. Using a static IP address avoids the potential issues that can arise with dynamic IP addresses, which can change and cause disruptions in communication.

  References:

  Axis Communications technical documentation and best practices for network device integration recommend the use of static IP addresses for reliable and consistent device management.

• Question 269:

  During a site survey, a client states that there will be no acoustical treatment to their new council chamber and they want a voice lifting (reinforcement) system.

  Which loudspeaker should be recommended to achieve optimal speech intelligibility?

  A. coaxial loudspeaker
  B. broad beam loudspeaker
  C. narrow beam loudspeaker
  D. ceiling mount loudspeaker
  C. narrow beam loudspeaker

  ---

  Explanation

  In a space with no acoustic treatment, a narrow beam loudspeaker is ideal for voice reinforcement as it can focus sound more precisely to reduce reverberation and enhance speech intelligibility. This directionality minimizes sound reflections that can degrade clarity in untreated spaces.

  CTS Technology Specialist Reference

  CTS materials on audio system design recommend narrow beam loudspeakers for environments with challenging acoustics to maintain intelligibility.

• Question 270:

  What is the best way to support new users after a conference room AV upgrade?

  A. Provide role-based training, simple operating procedures, common workflow practice, and a clear escalation path.
  B. Give users the complete engineering drawing set and skip hands-on instruction.
  C. Train only the facilities manager because end users should not need guidance.
  D. Hide support contact information so users try every control before asking for help.
  A. Provide role-based training, simple operating procedures, common workflow practice, and a clear escalation path.

  ---

  Explanation

  Operational support should help users perform the workflows they actually need, such as starting a meeting, sharing content, adjusting audio, and ending a session. Role-based training, concise procedures, practice, and escalation information reduce support calls and improve adoption. Engineering drawings alone are not user training.