Riverbed 830-01 Online Practice Questions and Exam Preparation

Riverbed 830-01 Online Questions & Answers

• Question 41:

  Users report that CIFS transfer speeds from a domain member server are much faster than from a domain controller. The Current Connections report confirms that connections to the domain controller show a red warning triangle. What configuration steps are required to resolve this issue?

  A. Domain Controllers should not be used for file sharing as they are always slower than domain member servers.
  B. The server-side SteelHead should be joined to the domain in Workstation mode, enable CIFS SMB Signing and Transparent Mode.
  C. Both the client-side and server-side SteelHeads should be joined to the domain in Active Directory Integrated mode.
  D. The client-side SteelHead should be joined to the domain in Workstation mode, enable CIFS SMB Signing and Transparent Mode.
  E. The server-side SteelHead should be joined to the domain in Active Directory Integrated mode, enable CIFS SMB Signing and Transparent Mode.
  C. Both the client-side and server-side SteelHeads should be joined to the domain in Active Directory Integrated mode.

• Question 42:

  Which of the following configuration policies are supported on the CMC appliance? (Select 4)

  A. Security Policy
  B. Optimization Policy
  C. System Setting Policy
  D. License Policy
  E. Networking Policy
  A. Security Policy
  B. Optimization Policy
  C. System Setting Policy
  E. Networking Policy

• Question 43:

  What is the command to return a Steelhead appliance back to factory defaults?

  A. (config) # restart factory reload
  B. (config) # reload factory
  C. (config) # restart clean
  D. (config) # reload clean empty
  E. (config) # reset factory reload
  E. (config) # reset factory reload

• Question 44:

  How does the Steelhead Mobile Controller provide Steelhead Mobile clients with the assigned policies and policy updates?

  A. Using the GID
  B. Using the SID
  C. Policies are pushed to all clients using IPSec
  D. The Steelhead Mobile client needs to be re-installed to update the policies
  E. Upon connection to the Steelhead appliance
  A. Using the GID

• Question 45:

  What should you do when you receive the following message?

  

  A. Nothing. This is a warning message which means that the Steelhead appliance is resetting an internal state regarding this connection and it should not affect user performance.
  B. Switch off the Steelhead appliance
  C. Create a specific pass-through rule to bypass the above source and destination hosts
  D. Reload the Steelhead appliance
  A. Nothing. This is a warning message which means that the Steelhead appliance is resetting an internal state regarding this connection and it should not affect user performance.

• Question 46:

  When deploying a Virtual Steelhead appliance, how much extra memory should be allocated for the extra VMware overhead?

  A. 3%
  B. 4%
  C. 5%
  D. 10%
  E. 2%
  C. 5%

• Question 47:

  On the Interceptor appliance, what are the possible filter settings on a load balancing rule? (Select 4)

  A. Source Port
  B. Source IP Subnet
  C. Destination IP Subnet
  D. Destination Port
  E. VLAN ID
  B. Source IP Subnet
  C. Destination IP Subnet
  D. Destination Port
  E. VLAN ID

• Question 48:

  To increase the high availability of a site at a remote office, you decided to install a second Steelhead appliance as an active/active serial cluster. However, after installing the second Steelhead appliance at the remote site, users started complaining about slow access to the data center. You have verified that this is not a duplex issue. At the data center location all users access the Internet which pass- through the Steelhead appliances. What is the most likely problem?

  A. SMB Signing
  B. Oplock issue
  C. The serial cluster Steelhead appliances are peering to each other
  D. Simplified routing was enabled on the secondary Steelhead appliance
  E. The datastore on the Steelhead appliances are wrapping
  C. The serial cluster Steelhead appliances are peering to each other

• Question 49:

  A customer would like to deploy the Interceptor appliance on four aggregated 100 Mbps links which use LACP to bundle the physical links into a single logical link. Which of the following is true? (Select 2)

  A. LACP is not supported with the Interceptor appliance
  B. The command "in-path multi-interface enable" must be configured
  C. The same IP address must be configured on each of the four in-path interfaces
  D. Each In-path interface should have its own unique IP address.
  E. The command "no arp filter response" should be enabled.
  D. Each In-path interface should have its own unique IP address.
  E. The command "no arp filter response" should be enabled.

• Question 50:

  What can be monitored via the CMC appliance? (Select 2)

  A. Currently logged in users to Steelhead appliances or the CMC appliance
  B. Command history per CMC appliance user
  C. Rogue Steelhead appliances on the network
  D. Current connections for an individual Steelhead appliance
  B. Command history per CMC appliance user
  D. Current connections for an individual Steelhead appliance